|
Kto jest w sklepie?
Sklep przegląda 5892 gości i 18 zarejestrowanych klientów
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SIF (NICAM/A2) ADJUSTMENT
No. Adjustment point 1 VCO COIL T2300 Adjusting condition/procedure 1. Receive �PAL COLOUR BAR� signal. 2. Connect DC Voltmater to Main Board socket SC304 pin 1. 3. Check and turn T2300 counter-clockwise (Left) so that DC voltmeter appear 0V, then turn it clockwise (Right) so that DC voltmeter appear 5V. After that , turn T2300 counter-clockwise (Left) until DC voltmeter appear 2.5 ± 0.1 Vdc. ** UNIT BOARD ADJUSTMENT Vcc IF Input Freq 5V ± 0.1Vdc 38.9MHz ± 10KHz Waveform or others 1 BEAM PROTECTOR
PROTECTOR OPERATION CHECKING
No. Adjustment point Adjustment condition/procedure 1) Receive "Monoscope Pattern" signal. 2) Set CONTRAST MAX. 3) Set BRIGHT MAX. 4) During the Collector & Emitter of Q853/4/5 short, make sure the protector ON and switch to standby mode. 1) Receive "Monoscope Pattern" signal. 2) Connect output of Bias Box to D602 cathode (C602 positive). 3) Set voltage of Bias Box to 18V and make sure the protector is not working. 4) Set voltage of Bias Box to 24.5V, and make sure the protector is working. 3 OTHER PROTECTOR 1) Once finish rectified Electrolytic Capacitor short testing in +B line, check all possible damaged components on +B line. (Use random selected set for inspection) Waveform or others * Select one of Q853/4/5 to do each short.
2
H, V PROTECTOR
Adjust T2300 until TP2300 (NICAM BOARD TEST POINT) become 2.5 ± 0.1Vdc. Check after assembly NICAM BOARD Test point: Main Board socket SC304 pin 1. Preset selected receptiion frequency (AFT OFF) Check Voltage 2.5 ± 0.1Vdc. Precaution: The Vcc, fo and other factors are considered in the unit board of the 1.0V tolerance which differ from the adjustment accuracy.
A/V INPUT, OUTPUT & COMPONENT IN CHECKING
No. Adjustment point 1 VIDEO AND AUDIO OUTPUT CHECK Adjustment condition/procedure 1) Receive the "PAL Colour Bar" signal (100% White Colour Bar, Sound 400 Hz 100% Mod.) 2) Terminate the Video output with a 75 ohm impedance. Make sure the output is as specified (1.0 Vp-p ±3 dB). 3) Terminate the Audio output with a 10K ohm impedance. Make sure the output is as specified (1.2 Vp-p ±3 dB). 1) Using the TV/VIDEO key on the remote controller, make sure that the modes change in order of TV, AV1, AV2 & TV again and the video & audio output are according to the input terminal for each mode. 1) Connect YUV & Audio signal to Component In terminal and Audio terminal. 2) Using the TV/VIDEO key on the remote controller, press it until the modes change to COMPONENT, confirm output appears. Waveform or others
13
2 3
VIDEO AND AUDIO INPUT CHECK
COMPONENT IN CHECK
21H-FV5RU
13-1
13-2
|
|
|
> |
|