|
|
|
Kto jest w sklepie?
Sklep przegląda 5895 gości i
1 zarejestrowany klient |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
 ;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD is in DVD mode with the tray open.) 2. To put the TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differ depending on the models.
5. After programming is finished, the tray opens automatically. Fig. e appears on the screen and the checksum will be shown in (*2).
"*******" differ depending on the models.
F/W Version Up Mode VERSION : Completed SUM : 7ABC
Model No : ******* VERSION : *.** ************.ab6
(*2)
F/W Version Up Mode
Model No : ******* VERSION : *.**
Please insert a DISC for F/W Version Up.
Fig. e Completed Program Mode Screen
6. 7.
EXIT: SELECT
Fig. a Version Up Mode Screen
8. 9.
The TV/DVD can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The TV/DVD enters the F/W version up mode automatically. Fig. c appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differ depending on the models.
At this time, no button is available. Remove the disc on the tray. Press [CH. o / p] button on the unit to go to TV mode, or press [POWER] button on the unit to turn the power off. Press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode again. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.
"*******" differ depending on the models.
MODEL : ******* Version : *.** Region : *
F/W Version Up Mode VERSION : (*1) Reading...
Model No : ******* VERSION : *.** ************.ab6
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. g
10.Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
"*******" differ depending on the models.
Fig. c Programming Mode Screen
The appearance shown in (*1) of Fig. c is described as follows:
No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK
EEPROM CLEAR : CLEAR
EXIT: SELECT
Programming... Writing new version data
Fig. h
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11.To exit this mode, press [CH. o / p] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
1-8-1
T9000FW
|
|
|
> |
|
