2359-2
4. When the character you want is at the cursor position, press C to move the cursor to the right. 5. Repeat steps 3 and 4 until the name is complete. � You can input up to eight characters for the name. 6. After you input the name, press C as many times as necessary to move the cursor to the number area. � You can input up to eight characters for the name. When the cursor is located at the eighth space of the name, moving the cursor to the right causes it to jump to the first digit of the number. When the cursor is at the 12th digit of the number, moving it to the right (by pressing C) causes it to jump to the first character in the name. 7. Use B and D to change the character (hyphen, number, or space) at the cursor position in the number area. The character changes in the following sequence.
ALARM
Alarm on indicator Timekeeping Mode time
You can set a Daily Alarm. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour. � The alarm and Hourly Time Signal operate in accordance with the current digital time (Timekeeping Mode time). � All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.
Press Press
. to . (space)
Alarm time Hourly time signal on indicator
8. When the character you want is at the cursor position, press C to move the cursor to the right. 9. Repeat steps 7 and 8 until you complete number input. � You can input up to 12 digits for the number. � The number initially contains all hyphens. You can leave the hyphens or replace them with numbers or spaces. 10. Press A to store your data and return to the Telememo record screen (without the cursor). � When you press A to store data, the message may appear on the display for a while, indicating that data is being sorted. After the sort operation is complete, the Telememo record screen appears.
To set the alarm time
1. In the Alarm Mode, hold down A until the hour digits of the alarm time start to flash. � This automatically turns on the alarm. 2. Press C to move the flashing between the hour and minutes. 3. While a setting is flashing, use D(+) to change it. � When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator). 4. Press A to return to the alarm display screen.
To recall Telememo records In the Telememo Mode, use D(+) and B(�) to scroll through Telememo records on the display. To edit a Telememo record 1. In the Telememo Mode, scroll through the records and display the one you want to edit. 2. Hold down A until the flashing cursor appears on the display. 3. Use C to move the flashing to the character you want to change. 4. Use B and D to change the character. � For details on inputting characters, see �To create a new Telememo record� (step 3 for name input and 7 for number input). 5. After making the changes that you want, press A to store them and return to the Telememo record screen. To delete a Telememo record 1. In the Telememo Mode, scroll through the records and display the one you want to delete. 2. Hold down A until the flashing cursor appears on the display. 3. Press B and D at the same time to delete the record. � The message appears to indicate that the record is being deleted. After the record is deleted, the cursor appears on the display, ready for input. 4. Input data or press A to return to the Telememo record screen.
Daily Alarm Operation
The alarm sounds at the preset time each day for about 20 seconds, or until you stop it by pressing any button. � The alarm and hourly time signal sound in all modes.
To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn the Daily Alarm and Hourly Time Signal on and off In the Alarm Mode, press B to cycle through the on and off settings as shown below.
Alarm On Indicator/Hourly Time Signal On Indicator
Alarm On Signal On
Alarm Off Signal Off
Alarm On Signal Off
Alarm Off Signal On
STOPWATCH
1/100 second
WORLD TIME
GMT differential City code
The stopwatch lets you measure elapsed time, split times, and two finishes. � The display range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds. � The stopwatch continues to run, restarting from zero
World Time shows the current time in 27 cities (29 time zones) around the world. � For full information on city codes, see the �CITY CODE TABLE�. � All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.
To view the time in another city code While in the World Time Mode, press D to scroll forward through the city codes (time zones) and B to scroll back. � If the current time shown for a city is wrong, check your Timekeeping Mode time and Home City code settings and make the necessary changes.
Current time in the selected city code
after it reaches its limit, until you stop it. � The stopwatch measurement operation continues even if you exit the Stopwatch Mode. � All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. Hours Seconds � The time on the screen may not appear to stop immediately when you press the button to stop an Minutes elapsed time operation or perform a split time operation in the Stopwatch Mode. Despite this, the time recorded by your button operation is accurate.
To measure times with the stopwatch Elapsed Time
Start Split Time Start Two Finishes Split Split release Stop Clear Stop Re-start Stop Clear
To toggle a city code time between standard time and Daylight Saving Time 1. In the World Time Mode, use B and D to display the city code (time zone) whose standard time/Daylight Saving Time setting you want to change. 2. Hold down A for about two seconds to toggle Daylight Saving Time (DST displayed) and standard time (DST not displayed). � The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is turned on. � Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected. � Note that you cannot switch between standard time and Daylight Saving Time while is selected as the city code.
Start
Split
First runner finishes.
Stop
Second runner finishes. Record time of first runner.
Split release
Record time of second runner.
Clear
