|
|
|
Kto jest w sklepie?
Sklep przegląda 5796 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
AR-150E 5) Tilt the DV box unit and rotate the DV18T clockwise to remove developer. 11) Face the toner supply port of the TH box unit upward, and press and insert the refill hose into the toner supply port with the toner bottle kept straight up. � Hold the left side of the TH box with your hand. � Press and insert the refill hose completely.
6) Clean the DV box unit by sucking or blowing with a vacuum cleaner to remove developer from the MG roller and toner from the DV box unit. Check that there is no toner or no foreign material attached to the connector and the gear. 7) Shake the developer bottle 10 times up and down, and remove the bottle cap and supply developer into the DV box unit. � � Slowly slant the bottle to supply developer evenly. Check the label to insure that developer is suitable for the model.
12) Lift the toner bottle and shake it left and right and supply toner until the bottle and the filling hose are empty. � It takes about one minute to fill toner completely in TH BOX UN from lifting the toner bottle to emptying the bottle and the hose. � If toner remains in the hose, when removing the hose from TH BOX UN, the remaining toner may disperse. Use great care for that.
8) Install the THBOX unit. � Insert two bosses of TH box on the drive side into the positioning hole of the DV box and fix together. 9) Remove the toner cap, look into the toner supply port and stop the THD Mylar at the position shown in the figure below. (Rotate the THK gear on the rear side of the TH box counterclockwise to rotate the TM shaft.) 10) Shake the toner box 20 times up and down, and remove the bottle cap and install the refill hose. Check the label to insure that toner is suitable for the model.
13) Check that there is no toner remaining in the bottle and remove the hose, and slowly pull and remove the hose. (If there is any toner remaining in the bottle or the hose, perform toner supply again.) Bend the refill hose and remove it from the TH box unit without dispersing toner. Attach the toner cap. � Attach the toner cap with the toner supply port of the TH box unit faced upward. 14) Clean the DV box unit with alcohol and attach the DV blade. � After drying the unit, attach the DV blade. � After attachment, check that there is no scratch and waves on the DV blade. � After attachment, be careful not to damage the DV blade. � Check that there is no foreign material in the DV blade and the section.
0.5 0
0.5
0
15) Install the DVF cover to the DV-TH box unit. 16) Clean the waste toner box unit and install it to the DV box unit. (Check that there is no toner in the waste toner box) Be careful of the pawl.
3�3
|
|
|
> |
|
