|
|
|
Kto jest w sklepie?
Sklep przegląda 5992 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
3.2
MEMORY IC REPLACEMENT
3.2.1 MEMORY IC This TV uses memory IC. This memory IC stores data for proper operation of the video and deflection circuits. When replacing the memory IC, be sure to use an IC containing this (initial value) data. 3.2.2 MEMORY IC REPLACEMENT PROCEDURE 1. Power off Switch off the power and disconnect the power cord from the wall outlet. 2. Replace the memory IC Be sure to use a memory IC written with the initial setting data. 3. Power on Connect the power cord to the wall outlet and switch on the power. 4. Confirm the system constant value � 12.SYSTEM (SYS) do not adjust normally. � The adjustment should not be done without signal. How to enter the SERVICE MENU. Confirm that the setting of TV/CATV SW is at the "TV" side and the setting of VCR/DVD SW is at the "VCR" side. (1) Before disappear the display of SLEEP TIMER settings, simultaneously press the [DISPLAY] key and [VIDEO STATUS] key of the remote control unit. (2) The SERVICE MENU screen will be displayed as shown Fig.1. How to enter the 12. SYSTEM(SYS). (1) While the SERVICE MENU is displayed, select 12.SYSTEM(SYS) item with [CH / ] keys, and [VOL / ] keys is pressed, the screen will displayed as shown in Fig.2. (2) Refer to the "12.SYSTEM(SYS)" table and check the the be the
SYS01 VIDEO IN Fig.2 SERVICE MENU SERVICE MENU
1. V/C(S)
3. SOUND(A) 7. LOW LIGHT 9. RF AFC 11. I2C BUS
2. DEF(D)
4. OTHERS(F) 6. 3L Y/C(LYC) 8. HIGH LIGHT 10. VOC 12. SYSTEM(SYS)
SELECT BY OPERATE BY Fig.1
EXIT BY EXIT
12.SYSTEM (SYS)
setting items. If the value is different, select the setting item with the [CH / ] keys and adjust the setting with the [VOL / ] keys. (The letters of the selected item are displayed in yellow.) (3) When adjustment has completed, the values store into memory IC automatically. (4) Press the [EXIT] key to return the SERVICE MENU screen. (5) Then press the [EXIT] key again to return the normal screen. 5. Receiving channel setting Refer to the OPERATING INSTRUCTIONS (USER'S GUIDE) and set the receive channels (Channels Preset) as described. 6. User settings Check the user setting items according to the "FACTORY SETTING ITEM" table. Where these do not agree, refer to the OPERATING INSTRUCTIONS (USER'S GUIDE) and set the items as described. 7. SERVICE MENU setting Verify what to set in the SERVICE MENU, and set whatever is necessary(Fig.1) . Refer to the SERVICE ADJUSTMENT for setting.
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
SLEEP TIMER key
DISPLAY & VIDEO STATUS key
V.STATUS
ASPECT LIGHT
C.C.
VOL
/ key
CH
/
key EXIT key
[RM-C1252G]
1-10 (No.52155)
|
|
|
> |
|
