Cassette Recorder
Cassette playback
1 2 3 4 5 6 1 2 � �
Adjust the source selector to TAPE/OFF. Press 9/ to open the cassette holder, and insert a cassette and close the deck.
Safety & Maintenance
1 2 3 4 CD synchro start recording Select CD source. Insert a CD and if desired, program track numbers. Press 9/ to open the cassette holder. Insert a blank tape and close the deck. Press 0 to start recording. � Playing of the CD program starts automatically from the beginning of the program. It is not necessary to start the CD player separately. For brief interruptions press ;. To resume recording, press ; again. To stop recording, press 9/. Recording from the Radio 1 2 3 4 Adjust the source selector to TUNER. Adjust BAND to FM or MW as your desired band. Tune to the desired radio station (see Radio reception). Follow steps 3-6 under CD sychro start recording. Recording your voice Select TAPE source. Follows steps 3-4 under Recording from the CD Player. Speak towards the built-in microphone (located on the left speaker, see 1). Follows steps 5 - 6 under Recording from the CD Player. � � � � � �
(See 7) Tape deck maintenance
To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special 1 2 3 4 head cleaning fluid to clean the deck. Open the cassette holder by pressing 9/. Press 1 and clean the roller C. Press ; and clean the heads A, and the capstan B. After cleaning, press 9. � Cleaning of the heads can also be done by playing a cleaning cassette through once.
Safety information
Place the set on a hard, flat and stable surface so that the system does not tilt. Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. � � Do not expose the apparatus to dripping or splashing. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. The ventilation should be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.. No objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. � To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. � � � �
Press 1 to start playback. To pause playback press ;. To resume, press ; again. To stop the tape, press 9/. Fast forwarding/rewinding Press 5 or 6 until you reach your desired passage. Press 9/ to stop rewinding/fast forwarding. Helpful hints : The keys are automatically released at the end of a tape and the set is switched off (unless PAUSE mode ; has been activated.) During fast forwarding/rewinding, the keys will not be released at the end of a tape. To switch off the set, make sure the cassette keys are also released. General information on recording 5 6
CD player and CD handling
If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. The lens of the CD player should never be touched! Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. Always close the CD-tape door to avoid dust on the lens. To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. Never write on a CD or attach any stickers to it.
�
�
Recording is permissible insofar as copyright or. other rights of third parties are not infringed. For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken.This deck is not suited for recording on CHROME (IEC II) or
�
1 2 3 4
�
METAL (IEC IV) type cassettes. The best recording level is set automatically. Altering the VOLUME will not affect the recording. To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape.
�
�
