PHILIPS AZ3011/05
Instrukcja Obsługi

CD PLAYER
CD Player Display indication for CD functions Selecting a different track During playback you can use � or § to select a � CD open: CD door open (See 6) particular track. � disc: CD inserted (See 7) � If you have selected a track number in the stop or � In stop mode: total track number and total pause position, press 2; to start playback. playback time � Press § once briefly for the next track, or press � During CD playback: elapsed playback time of repeatedly until the desired track number appears current track and current track number in the display. � Pause: elapsed playback time freezes and flashes � Press � once briefly to return to the beginning of (See 8) a current track. � shuffle/ repeat modes: when the respective mode � Press � more than once briefly for a previous is activated track. � prog: when CD programme active); prog also appears briefly when you store a track (See 9) � no sel: programme activated but no tracks selected (See 0) � full: programme memory full (See !) � no prog: programme cancelled (See @) � no disc: no disc/ error in CD operation /CD-R(W) is blank or the disc is not finalized (See # + Troubleshooting) Playing a CD This CD-player can play Audio Discs and CDRecordables. Do not try to play CD-Rewritables, a CD-ROM, CDi, VCD, DVD or computer CD. 1 Adjust the source selector to CD. � Display: shows Cd briefly. 2 To open the CD door, lift the CD door at the edge marked LIFT TO OPEN. 3 Insert a CD or CD-R with the printed side facing up and press the CD door gently close. 4 Press 2; on the set to start playback. 5 To pause playback press 2;. To resume, press 2; again. 6 To stop CD playback, press STOP 9. Note: CD play will also stop when: � you open the CD compartment; � you select TUNER sound source; � the CD has reached to the end. Finding a passage within a track 1 Press and hold down � or §. � The CD is played at high speed and low volume. 2 When you recognize the passage you want release � or §. � Normal playback resumes. Different play modes: Shuffle and Repeat PROG MODE allows you to select various play modes. The modes can be selected or changed during playback of an entire CD/ CD programme in the following sequence: shuffle � all tracks are played in random order shuffle repeat all � repeats the entire CD in random order repeat � plays the current track continuously repeat all � plays the entire CD continuously 1 During playback, select your play mode by pressing PROG MODE once or more until the desired play mode is shown. � Display: your selected mode flashes 2 seconds before playback � You can use � or § to skip tracks during the shuffle/ repeat modes. � The shuffle/ repeat play options can be combined and used with a programme: e.g. shuffle/ repeat all repeats the entire CD programme in random order. 2 To return to normal playback press PROG MODE until the shuffle/ repeat modes are no longer shown. � You can also press 9 to quit the play mode.

CD PLAYER
Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the STOP mode, press � or § for your desired track. 2 When your chosen track number appears, press PROG MODE once to store the track. � The display shows prog and prog briefly followed by your selected track number. (See 9) � If you attempt to programme without first selecting a track number, no sel is shown. (See 0) 3 Repeat steps 1 to 2 to select and store all desired tracks in this way. � full is displayed if you attempt to programme more than 20 tracks.(See !) 4 To play your programme, press 2;. Reviewing your set programme

MAINTENANCE & SAFETY
Precautions & General Maintenance (See $) � Place the set on a hard and flat surface so that the system does not tilt. � Do not expose the set, batteries or CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. � Do not cover the set. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. � The mechanical parts of the set contain selflubricating bearings and must not be oiled or lubricated. � To clean the set, use a soft dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. CD player and CD handling (See %)

� In the STOP mode, press and hold down � The lens of the CD player should never be touched! PROG MODE for more than one second. � Sudden changes in the surrounding temperature � The display shows all your stored track numbers can cause condensation to form and the lens of in sequence. your CD player to cloud over. Playing a CD is then Erasing a programme You can erase the contents of the memory by: � opening the CD door; � selecting TUNER source; � pressing 9 (twice during playback or in the stop position � Display: shows no prog briefly when the programme is cancelled.(See @) not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. � Always close the CD door to keep the CD compartment dust-free. To clean, dust the compartment with a soft dry cloth. � To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. � Never write on a CD or attach any stickers to it.