|
|
|
Kto jest w sklepie?
Sklep przegląda 6039 gości i
1 zarejestrowany klient |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
SETTING CLOCK RESETTING THE MICROCOMPUTER
In this example, clock is set for 12-hour (AM 12:00) sysReset microcomputer under the following conditions:
1 Press ON/STAND-BY button to enter stand-by mode. q If the display is not correct. MEMORY/SET
q If the operation is not correct. POWER
X-BASS/ (Main unit operation) tem. q To erase all of the stored memory contents (clock and timer DEMO settings, tuner and CD presets).
ON/ ON/ Press ON/STAND-BY button to enter the stand-by mode. STAND-BY STAND-BY
Press the CLOCK button. POWER Within 5 seconds, press the MEMORY/SET button.
1 3 2 While pressing down button and the X-BASS/DEMO
display mode. second. "AM 12:00" � The 12-hour display q "CLEAR AL" will appear. "AM 0:00" � The 12-hour display will appear. TIME "0:00" � The 24-hour display will appear. (0:00 23:59) q Note that this can only be set when the unit is first installed or it has been reset.
presets.
2
CLOCK 4 Press TUNING/TIME ( or ) to select time button, hold down the ON/STAND-BY button for at least 1
TUNING/ (AM 12:00 PM 11:59) Caution:
q The operation explained above will erase all data stored in (AM 0:00 PM 11:59) memory including clock timer settings, tuner and CD ( )
5 Press the MEMORY/SET button. 2 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, "AM" will change automatically to "PM".
3
7 Press the MEMORY/SET button.
minutes. q Press the TUNING/TIME ( or ) button once to advance minute intervals. q The hour setting will not even if minutes advance from "59" to "00". q The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.
4 8 Press TUNING/TIME ( o r ) button to adjust the
OPERATION MANUAL
�5�
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds. Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power failure occurs or after the AC power cord is disconnected. time.
12:00 AM 0:00 by 1 minute. Hold it down to change the time in 5
5 9 Press the MEMORY/SET button.
6
7
8 If this happens, follow procedure below to change the clock
To change the clock time:
9 xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button. zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
CD-BA150
yPerform steps 1 9 above.
|
|
|
> |
|
