PANASONIC CWXC123VU
Instrukcja Obsługi

WINDOW REQUIREMENTS
� Hot sun rays hitting the outside surface of the cabinet will create considerable heat load. If the outside of the cabinet is exposed to direct sunlight, consider building an awning to shade the cabinet 22 to 42-1/8� while providing ample area for the heated air to be exhausted from the condenser (both sides) and the top. This unit is designed for installation in standard double hung windows. NOTE The unit may also be installed �through the wall�. You should, however, observe standard carpentry practices and frame the opening without violating local ordinances.

CHASSIS INSTALLATION INTO THE CABINET
1 Slide the chassis into the cabinet. 2 Reinstall the cabinet screws.

Secure the cabinet to chassis by using screws (from rear cabinet).

°F

hr

TEMP/TIME R

TIMER
SET

OPERATION

COOL FAN HIGH MED LOW FAN SPEED MODE

SET/ CANCEL

OFF/ON

AIR SWING

ECONOM

Y

Wirel
Remot e Cont r ol

ess

INSTALLATION PROCEDURES
1 Remove the rear cabinet
1515 /16� (min)

INSTALLATION OF THE FRONT GRILLE Depending upon the location of the AC outlet, route the AC cord to either the left or right side while installing the front grille.
COOL FAN HIGH MED LOW FAN SPEED MODE AIR SWING

screws and save for later use.
2 Slide the chassis out from the

cabinet.

COOL FAN MODE

HIGH FAN SPEED LOW

MED

°F hr
TEMP/TIMER

TIMER
SET

OPERATION

SET/ CANCEL

OFF/ON

AIR SWING

ECONOMY

Remote Co ntrol

Wireles s

HOW TO ASSEMBLE THE EXPANDABLE PANELS
Top angle Top sealing ribbon (To be attached to the top angle) Type B screws Expandable panel

°F

hr

TEMP/TIM

ER

TIMER
SET

OPERATION

SET/ CANCEL

OFF/ON

ECONOM

Y

Remote

Wirel ess Control

This figure shows the AC cord routed to the left side. 1 Place the front grille on the Side sealing ribbon (To be attached to the expandable panel) Type C screws

cabinet first.
2 Secure the front grille to the
°F
MED FAN SPEED LOW MODE

TIMER
TEMP/TIME R SET

OPERATIO N

hr

main chassis using screw provided. INSERT THE Attach the (part no. CZ-SF6P) to the frame.

COOL FAN

AIR SWING

HIGH

Remote Co ntro

Wirel

SET/ CANCEL

OFF/ON

ECONOM

Y

ess l

NOTE This procedure applies to left and right of assembling expandable panel.

� Attach the top angle to the cabinet using screw type B (3 pcs). � Insert expandable panels to cabinet sides as shown. � Secure the first fold of expansion panel to cabinet using screw type C (3 each). CABINET INSTALLATION
1 Cut the �Sealing Ribbon� to the

Slot in the and the frame (part no. CZ-SFW6P) to the front grille.

proper length, and attach it along the bottom edge of the bottom window sash.
2 To prevent condensation water

Window sash sealing ribbon

COOL

FAN

HIGH MED LOW

MODE

°F

TIMER
TEMP/TIME R SET

OPERATION

hr

SET/ CANCEL

OFF/ON

AIR SWING

ECONOMY

FAN SPEED

Wirele
R e m o t e Co n tro

ss l

from dripping inside, the cabinet should be installed level or very slightly tilted to the outside.
3 Secure the cabinet using screws. Type A screw Type B screws Window sill Type A screws Inside of sash Top angle Expandable panel Window sash foam seal Outside of sash Window sash Sealing ribbon

The and the frame can be obtained separately from your nearest servicenter. INSERT THE AIR FILTER

Attach the air filter to the intake grille
°F
COOL FAN MODE LOW

hr

TEMP/TIME

R

AIR SWING

HIGH MED FAN SPEED

Remote

Wirele ss Control

SET/ CANCEL
SET

TIMER

OPERATION

OFF/ON

ECONOMY

PLACE FRONT INTAKE GRILLE OVER THE FRONT GRILLE Slide the front intake grille slightly to the right to reattach the tabs and then push it down to close tight.

� Expand the expandable panel fully into the grooves of the window frame, secure the expandable panel, left, right and top mounting frames to the bottom of the window sash using 4 screws type A and 2 screws type B. � Secure the cabinet using wood screws type A. � Cut the window sash foam seal to the proper size and seal the opening between the top of the inside window sash and the outside window sash. Note : If a gap exists between the unit and window sash, you may use �Sealer� supplied with the installation kit for a better seal.

°F
HIGH MED LOW

TIMER
TEMP/TIME R SET

OPERATION

hr

SET/ CANCEL
MODE AIR SWING

OFF/ON

COOL FAN

ECONOMY
FAN SPEED

Wireless
Remote Control

Lift up about 90°.