|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
- SERVICING NOTES
- GENERAL
- DISASSEMBLY
- SERVICE MODE
- ELECTRICAL ADJUSTMENTS
- DIAGRAMS
- Block Diagram - MAIN Section
- Block Diagram - POWER SUPPLY Section
- IC Pin Function Description
- Printed Wiring Board
- Schematic Diagram
- EXPLODED VIEWS
- ELECTRICAL PARTS LIST
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
 ;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
SECTION 4 SERVICE MODE
Service Mode (Service program) The equipment is provided with a service program built in the microcomputer, like conventional models. Service program operation methods are described in the following.
PLAY MODE Tracking servo and sled servo are turned ON REPEAT/ENTER Tracking gain-up mode while pressing
4. By pressing the ^ key, focus is turned ON from focus searching while entering CLV-S. (draw-in mode) Without disc, focus searching is repeated continuously. 5. By pressing the PLAY MODE key, tracking servo, sled servo and CLV-A (servo in PLAY) are turned ON. 6. When step 4 and 5 are performed, playing begins. No muting is ON in the service mode. 7. By pressing the p key, all servos (focus, tracking and sled) are turned OFF. However, the disc motor revolves for a while by inertia. � Step 3 (Resetting of service mode) 1. Be sure to disconnect the external power supply and remove the solder bridge at the TEST terminals connected before in setting. 2. The set thus becomes available for normal operation.
HOLD c Be sure to turn OFF the HOLD switch (If ON, all the LCD indication and LED are light up)
� MAIN BOARD (Side A) � = (FR) The optical pick-up is moved inwardly + (FF) The optical pick-up is moved outwardly
^ (PLAY/PAUSE) Focus is tuned ON to effect draw-in mode p (STOP)
[All servos are turned OFF]
Descriptions in [ ] indicate major operations in the service mode. For more informatrion, see Step 2.
Fig. 1 Layout of each key
� Step 1 (Service mode setting methods) 1. Turn OFF the HOLD switch with external power supply disconnected. (power is not applied to the set) 2. Solder across the TEST terminals (TAP802). (pin %¢, IC801 (ESPSL/TEST) is grounded) 3. Connect an external power supply. Thus, the set is switched to the service mode. � Step 2 (Operation in the service mode) 1. Once the service mode is effected, the LCD displays 5 indications each of which is repeatedly displayed. However, the following operations can be activated even if LCD indication is effected. 2. By pressing the + or = key, the optical pick-up is movable inwardly or outwardly. However, if this is activated, tracking servo and sled servo are turned OFF, so it can be turned ON by pressing the PLAY MODE key if required. 3. By pressing the REPEAT/ENTER key, the tracking gain-up mode becomes active.
TAP802 (TEST)
Fig. 2 Location of Test terminal
�8�
|
|
|
> |
|
