PIONEER DJM-3000/WAXCN
Instrukcja Serwisowa

5

6

7

8

Rotate clockwise to increase response (to +12 dB), and rotate counterclockwise to decrease response (to �26 dB). = H.P CUE (Headphones cue switch) When this switch is pressed it lights orange and the corresponding channel is output to headphones. When the switch is pressed again the light goes out and the channel�s output to the headphones is cut. When the beat effector function is set to AUTO BPM, this switch functions to select the BPM display channel. ~ Peak level meter Peak levels are displayed as they occur and maintained for 2 seconds. Displays output level before channel fader adjustment. Displayable range is from �22 dB to +14 dB. ! Channel fader lever Use to adjust the sound level at each channel.

At the center click position, the master output and source selected with the H.P CUE switch are at equal levels. ( LEVEL control Use to control the headphones monitor level. When one of CH-1 to CH-4 is selected, this control is not affected by the MASTER fader lever (%) and the MASTER BALANCE control (^). ) PHONES (headphones jack)

A

� Cross Fader Controls
_ CROSS FADER ASSIGN A switch When using the cross fader with two sources (A, B), this switch selects the source assigned to A. THRU: When cross fader is not used, sets to THRU. 1-4: Use to select the channel (CH-1 to CH-4) assigned to A. Channels other than those assigned to A and B can be output without passing through the cross fader. + CROSS FADER CURVE selector switch Use to select one of three rising curve patterns for the cross fader function. ¡ Fader display A During the effect mix mode, displays the output of sounds from the channel selected with the CROSS FADER ASSIGN A switch. � Cross fader lever Use to adjust the mix of sounds from the sources assigned to A and B by the ASSIGN switches (_) and (¢). £ Fader display B During the effect mix mode, displays the output of sounds from the channel selected with the CROSS FADER ASSIGN B switch. ¢ CROSS FADER ASSIGN B switch When using the cross fader with two sources (A, B), this switch selects the source assigned to B. THRU: When cross fader is not used, sets to THRU. 1-4: Use to select the channel (CH-1 to CH-4) assigned to B. Channels other than those assigned to A and B can be output without passing through the cross fader.

B

� MASTER (Master Controls)
@ MONO/STEREO selector switch Use to select whether the master output and booth monitor output are monaural or stereo. # MASTER LEVEL meter Displays output level following adjustment of the MASTER fader lever, and holds the display for 2 seconds. Displayable range is from �22 dB to +14 dB. $ H.P CUE (Headphones cue switch) When this switch is pressed it lights orange and the master output is heard in the headphones. When the switch is pressed again the light goes out and the master output to the headphones is cut. % MASTER fader lever Use to control the master output level. The rear panel MASTER LEVEL ATT. control can also be used to reduce the output level. ^ MASTER BALANCE control Use to adjust the balance of right-left channels for master output and booth monitor output.

C

[ BOOTH MONITOR Control
Use to adjust the output at the BOOTH MONITOR connectors on the rear panel. Not affected by the MASTER fader lever (%).

D

\ FADER START Switches � POWER Switch ] HEADPHONES Controls
& MONO SPLIT/STEREO selector switch Use to select whether to split monitor sound on the left and right of the headphones or to keep sound in stereo form. When set to MONO SPLIT, the headphones output is set to 2-channel monaural; the Left channel becomes the source selected with the H.P CUE switch, while the Right channel becomes the master output sound (only when MASTER H.P CUE switch is set to ON). * MIXING control Use to adjust the headphones monitor sound. When rotated fully clockwise, the master output sound only is heard (only when MASTER H.P CUE switch is set to ON). When rotated fully counterclockwise, only the channel selected with the H.P CUE switch (other than MASTER) is heard. CH-1, CH-2, CH-3, CH-4 When a CD player (CMX-3000, CMX-5000, CDJ-1000, CDJ100S, CDJ-700S or CDJ-500II) is connected to one of the above channels of this unit via a control cord, the CD player�s CUE START/STOP operation will start when the channel fader is moved from �0� upwards, and will stop (back cue) when the channel fader is returned to �0�. The indicator of the selected channel will light orange during this operation. Also, if a channel is assigned to the cross fader, the cross fader is given priority; when the Cross fader lever begins moving from the A side toward B side, the CD player assigned to the B side will start, and when the lever reaches the B side, the A side source will stop (back cue).

E

F

DJM-3000
5 6 7 8

105