|
|
|
Kto jest w sklepie?
Sklep przegląda 5927 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
DR-R7181
8. PANEL FACILITIES AND SPECIFICATIONS
REARVIEW
1 2 34
5
6
7
ON
WIRING MONITOR IND SCSI TERM IND PARITY ON / OFF TERM ON / OFF
RELEASE LOCK
SCSI ID
8
9
1 SCSI termination switch
This switch is used to turn the drive's internal SCSI termination switch on and off. Note that this switch is set on at the time of shipment.
5 Changer interface cable
This cable must be connected to the changer-internal changer interface connector.
6 Power cable 2 Parity switch
When the parity switch is turned on odd parity checking is performed by the CD-R drive for all data read in from the SCSI data bus, and when the parity switch is turned off no parity checking is performed. Note that a parity bit is assigned to each byte of output data transmitted from the CD-R drive whether the parity switch is turned on or off. This cable must be connected to the power inlet located in the changer.
7 Lock lever
When a drive is to be removed from the changer, flip the lock lever to the released position and then pull the drive out from the changer.
3 Termination indicator
When the drive is installed in a changer and its power cable has been connected, this indicator lights up if the drive's SCSI termination switch has been turned on.
8 SCSI ID switches
These switches are used to set the drive's SCSI ID. Pressing the upper switch causes the displayed SCSI ID to be decremented, and pressing the lower switch conversely causes the SCSI ID to be incremented. Note that SCSI ID is set to '0' at the time of shipment.
4 Wiring monitor indicator
Meaning of indicator when indicator is lit up: ¶ Indicates that a disc has been inserted into the drive. ¶ This indicator also lights up when the drive is installed in a changer and its power cable has been connected. Meaning of indicator when indicator flashes in 2-second intervals: ¶ This indicator flashes in 2-second intervals when the drive is installed in a changer and its changer interface cable has been connected. Meaning of indicator when indicator flashes in 0.5-second intervals: ¶ This indicator flashes in 0.5-second intervals when the drive in question has been specified as the drive to be swapped during the swapping of drives.
9 SCSI interface connector
This connector must be connected to the SCSI cable provided with the changer or to an add-on SCSI cable.
NOTE:
Be careful not to allow any part of your body to come into contact with connector pins, as doing so may result in faulty connections or damage from static electricity.
22
|
|
|
> |
|
