Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5660 gości 
Kategorie
Informacje
Polecamy
Strona główna >> ONKYO >> DTR-6 Instrukcja Obsługi
 
 0 szt. w koszyku 

ONKYO DTR-6
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis ONKYO DTR-6 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!
Recenzje innych produktów
 CLD3760K PIONEER Instrukcja Obsługi by Sebastian Twardowski;
Dobrej jakości skan - wkońcu mogłem poznać wszystkie funkcje tego odtwarzacza - polecam .
 CDV475 PHILIPS Instrukcja Obsługi by Sebastian Twardowski;
Gruba instrukcja - poprostu wszystko co potrzreba - polecam .

Tekstowy podgląd strony 29 (kliknij aby zobaczyć)
Selecting an input source
� Using the on-screen display
1. Press the OSD MENU button. 2. Select �Input Selector� and then press the right edge of the ENTER/Cursor button. 3. Select �Digital Input Setup� and then press the right edge of the ENTER/Cursor button. The �Digital Input Setup� screen appears. To display VIDEO 2 and later items, press the lower edge of the ENTER/Cursor button. � Select the digital input connector from among �OPTICAL 1,� �OPTICAL 2,� �COAXIAL 1,� �COAXIAL 2,� and �� � � �.� � If no digital input connector is assigned to the selected input source, it will be indicated as �� � � �.� � To enter the setting, move the cursor vertically using the ENTER/Cursor button. 4. To set the input signal format, move the cursor to the line immediately below the input source and then press the right or left edge of the ENTER/Cursor button. � Select the digital audio format from among �Automatic,� �Digital,� �Analog,� �PCM,� and �DTS.� � Holding down the right or left edge of the ENTER/Cursor button sequentially changes the setting. 5. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode. Notes on DTS 1. If you play a CD or LD that supports DTS when the �Analog� or �PCM� setting is selected on the DTR-7/DTR-6, the DTS encoded signal will not be decoded and noise will be output. This noise could damage the amplifier and speakers. Therefore, be sure to select �Automatic�, �Digital� or �DTS� and use the digital input jacks (OPTICAL1/2 /COAXIAL1/2) to connect the DTS source. 2. If you play a CD or LD that supports DTS when the �Automatic�, or �Digital� setting is selected, you may hear a noise for a short while until the DTS decoder recognizes the DTS encoded signal and starts operating. This is not a malfunction. 3. If you press the PAUSE or SKIP button on the player while playing a DTS source, a short noise may be heard. This is not a malfunction. In such cases, try playing the source in the �DTS� mode. 4. The DTS indicator on the DTR-7/DTR-6 lights up while it plays the DTS source. When playback concludes and the DTS signal transmission stops, the DTR-7/DTR-6 remains in DTS mode and the DTS indicator remains lit. This prevents noise when you operate the PAUSE or SKIP button on the player. Therefore, if the source switches from the DTS signal to the PCM signal immediately, the PCM signal may not be played. In this case, stop the playback of the source on the player for about three seconds, then resume playback. 5. Some CD players and LD players may be unable to play DTS sources correctly even if you connect the player to the DTR-7/ DTR-6 digitally. This is because the digital signal has been processed (such as the output level, sampling frequency, frequency response, etc.), and the DTR-7/DTR-6 cannot recognize the signal as DTS data. Therefore, you may hear noise when you play a DTS source while processing the signal. 6. The OUT jacks of the VIDEO-1, VIDEO-2, and TAPE connectors output analog audio signals. Do not record CDs or LDs that support DTS using these jacks. Otherwise, you will record a DTS-encoded signal as noise.

* Digital Input Setup * CD DVD VIDEO 1 :COAXIAL 1 Automatic :COAXIAL 2 Automatic :---Automatic

29

Klienci kupując ten produkt kupili także

$4.99

DTR-6 ONKYO
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.166 - Number of Queries: 104 - Query Time: 0.047