PHILIPS DVDR80/0X1
Instrukcja Serwisowa

EN 204

9.

DVDR80/0x1

Circuit-, IC descriptions and list of abbreviations
reception, an additional circuit for suppressing the audio carrier of the adjacent channel is used. This circuitry is adjusted by coil [5710] for maximum suppression at 40.4MHz.

The feedback control for the switched-mode power supply is done by changing the conductive phase of the switching transistor so that either more or less energy is transferred from the rectified mains voltage at [2309] into the transformer. The regulation information is provided by voltage reference [7315]. This element compares the 5V-output voltage via voltage divider [3332, 3333, 3334] with an internal 2.5V reference voltage. The output voltage of [7315] passes via an optocoupler [7314] for insulation of primary and secondary parts as a current value into pin 3 on the IC [7313]. The switchon time of the transistor [7307] is inversely proportional to the value of this current.

Overload, power limitation, burst mode: With increasing load on one or more of the power supply outputs, the switch-on time for the power transistor [7307] increases, and thus also the peak value of the delta-shaped current through this power transistor. The equivalent voltage of this current profile is passed from resistors [3321] and [3352] via [3365] to pin 5 of the IC [7313]. If the voltage on pin 2 reaches approx. 0.4V in one switching cycle, the conductive phase of the switching transistor is ended immediately. The check is done in each individual switching cycle. This process ensures that no more than approx. 60W can be taken out from the mains ( = power limitation ). If the power supply reaches the power limit, the output voltages and the supply voltage Vcc on pin 1 of the IC [7313] will be reduced following further loading. If Vcc is less than approx. 9V at any point during this process, the output of the IC [7313, pin 6] is blocked. All output voltages and Vcc decrease and a new start-up cycle begins. If the overload status or short-circuit remains, the power limitation will be activated immediately and the voltages will again decrease, followed by another start-up cycle ( Burst Mode ). The amount of power taken up from the mains in burst mode is low. Standby modes: In the �AV-Standby� operating mode of the set, the �ION� control line is primarily used to switch off all output voltages for Basic Engine and Digital Board (supplies 3V3, 5V, 12V, 5N and 4V6 at Connectors 1932 and 1933) of the power supply. This reduces the amount of power taken from the mains. In Low Power Standby mode additionally the �STBY� control line is used to switch off output voltages 5SW and 8SW. This reduces power consumption to less than 3W, if additionally the display is switched off. The power supply will continue operating in Standby mode with a switching frequency of approx. 25 kHz.
9.3.3 Frontend This unit is designed to support two basic versions, which are distinguished by a different assembly variant only (one for multistandard and the second for Pal-I only) and comprises the following parts: � Tuner UV1316K [1705] � IF amplifier & video demodulator IC TDA 9818/9817 [7710] � Sound processor MSP3415G [7600]

IF demodulator The signal from the tuner and IF-selection circuit is processed by the demodulator IC TDA 9818/9817 [7710]. The signal �PSS� to pin 3 switches between demodulation of positive (SECAM only) or negative modulated video carriers. A QSSaudio-IF signal SIF1 is generated for demodulation in the sound processor [7600]. The audio-IF carrier is selected in the audio SAW filter [1702]. This filter is switched for SECAM L�. If the signal �SB1� is �high�, the switch [7714] is closed and the diode [6705] is not conducting. For all other standards the diode [6705] is conducting and the switch [7714] is open. The output signal of this SAW filter is firstly processed in the TDA 9818. Audio carriers are converted from the tuner IF level to the audio IF position and further processed in the audio demodulator [7600]. The AFC coil [5711] on the TDA 9818/ 9817 is adjusted so that when a frequency of 38.90 MHz is supplied to the IF output of the tuner, the AFC voltage on pin 17 of [7710] is 2.5V. The setting of the picture carrier frequency for SECAM L in the TDA 9818 is achieved by connecting pin 7 of the IC via a resistor [3710] to ground. The switch [7701] and the signal �SB1" do this. The HF-AGC is set using the potentiometer [3724] so that, with a sufficiently large antenna input signal (74 dB V), the voltage at the IF output of the tuner [1705] pin 11 is 500 mVpp. This setting must be carried out when the audio carrier is switched off. The demodulated video signal appears on pin 16 of [7710]. The AGC voltage at pin 4 is used to determine the antenna signal strength after a buffer [7717] with the signal �AGC� and an analog input port of the CC-P. The trap [1704] reduces the sound carrier remainders in the video for BG standards. The trap [1706] works in the same way for the Pal-I standard only. For all other standards the switch [7713] is closed via [7706] and �SFS_TS�-line set �high" to bypass this trap. In these cases the selectivity of the SAW filter [1701] is sufficient. The coil [5713] for non-BG standards realizes a frequency response correction. This correction is not desired for SECAM L' and therefore short-circuited by [7716] (signal SB1 is �high� and [7702] has on-status). The demodulated video signal �VFV� is available after the buffer and limiting stage for noise peaks [7711]. The FM-PLL demodulator function of TDA 9818 is not necessary and therefore deactivated by the resistor [3739]. Audio demodulator The sound demodulation is done by the MSP3415 [7600], which is also fully controlled via I C-bus by the CC-P (determination of bandwidth, amplitude, standard, ...).The audio signals are available at pin 30 and pin 31 of [7600] and fed as �AFER�- & �AFEL�-line to the audio-I/O for further processing.

Tuner and IF selection The Tuner [1705] converts the RF-signal coming from the antenna input to an IF-signal. The tuner is fully controlled via I C-bus of the CC- P. [1705] is also equipped with a �passiveloop-through� between antenna-in and -out to save power in stand-by of the set, when the complete part is not supplied. The IF frequency of the video carrier is 38.9 MHz for all systems except SECAM L' (34,0 MHz). A quasi-split audio system is used. Separate surface-wave filters (SAW) are required. [1701], [1703] for video, [1702] for audio. [1701] is switched into the signal path for DK/I-SECAM L/L' reception, if the signal �SFS_TS� is �high�. In this case the switches [7704], [7705] are open and the diode [6703] is conducting. [1703] is switched into the signal path for BG reception (�SFS_TS� is �low�). Then the switch [7712] is open and the diode [6704] is conducting. For DK/I-SECAM L/L'