CASIO DW8600KJ-7T
Instrukcja Obsługi

2-2. QW-1629
GENERAL GUIDE
� Press C to change from mode to mode. � After you perform an operation in any mode, pressing C returns to the Timekeeping Mode.
Sunrise/Sunset Mode

Press C

Timekeeping Mode
A B Press D Press C Moon Data Mode Press A Stopwatch Mode C D Tide Graph Mode

Alarm Mode

(Timekeeping Display)

(Temperature Display)

TIMEKEEPING FUNCTIONS
Temperature graph Day of week
A

ABOUT THE BACKLIGHT
About the Auto Light Switch Function
When the auto light switch function is turned on, the backlight automatically turns on for two seconds under the conditions described below. Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light switch to operate when not needed, which shortens battery life. Moving the watch to a position that is parallel to the ground and then tilting it towards you approximately 40 degrees causes the backlight to illuminate.

Tide graph

Month and Moon Day graph
B

There are two different displays in the Timekeeping Mode: a Timekeeping Display and a Temperature Display. Use D to switch between them. � Both the Timekeeping Display and the Temperature Display show the temperature bar graph. � Holding down A while the Timekeeping Display is shown enters the time and date setting mode. Holding down A while the Temperature Display is shown enters the temperature calibration mode. � When in the Timekeeping Mode, press B to illuminate the display.

C

D

Minutes Hour AM indicator Seconds

Parallel to ground 40�

To set the time and date
1. Press D to display the timekeeping display (with the month and day). 2. Hold down A and the seconds digits flash on the display because they are selected. 3. Press C to change the selection in the following sequence. Seconds Day of week Hour Day Minutes Month 12/24-Hour Format Year � The backlight may not illuminate if the face of the watch is more than 15 degrees off parallel to the left or right. Make sure that the back of your hand is parallel to the ground.
Parallel to ground More than 15 degrees too high More than 15 degrees too low

4. While the seconds digits are selected (flashing), press D to reset the seconds to �00�. If you press D while the seconds count is in the range of 30 to 59, it is reset to �00� and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the minutes count is unchanged. 5. While any other digits (besides seconds) are selected (flashing), press D to increase the number or B to decrease it. Holding down either button changes the current selection at high speed. � While the 12/24-hour setting is selected, press D to switch between the two formats. 6. After you set the time and date, press A twice to return to the timekeeping display. � The date can be set within the range of January 1, 1995 to December 31, 2039. � If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the timekeeping display automatically.

� Static electricity or magnetic force can interfere with proper operation of the auto backlight function. If the auto backlight does not illuminate, try moving the watch back to the starting position (parallel with the ground) and then tilt it back toward you again. If this does not work, drop your arm all the way down so it hangs at your side, and then bring it back up again. � Under certain conditions the backlight may not light until about one second or less after turn the face of the watch towards you. This does not necessarily indicate malfunction of the backlight. In the Timekeeping Mode, hold down D for one or two seconds to turn the auto light switch function on and off.
Auto light switch indicator

To switch the auto light switch function on and off

Important
� After you change a setting in the above procedure, the watch needs a bit of time to calculate certain information. During this calculation, the patterns in the graphic display move at high speed. Wait until the patterns stop moving before you try to input any further data. � If you set the current time forward one hour for daylight saving time (summer time), be sure to also increase the setting for your difference from Greenwich Mean Time (see �To set location data� below). Of course, you should remember to adjust the other way (by decreasing the difference) when you go back to standard time.

D

Hold down D

D

ON

OFF

To set the location data
GMT differential Latitude
A B

1. Use C to enter the Timekeeping Mode. 2. Press D to display the Timekeeping Display. 3. Holding down A and the seconds digits flash on the display. 4. Press A again to display the location data. The GMT differential data is flashing because it is selected. 5. Press C to change the selection in the following sequence.
GMT differential Longitude/Latitude

� The auto light switch indicator is shown on the display in all modes while the auto light switch function is on. � In order to protect against running down the battery, the auto light switch function is automatically turned off approximately three hours after you turn it on. Repeat the above procedure to turn the auto light switch function back on if you want. � Pressing B while in the Timekeeping Mode illuminates the display, regardless of the auto light switch's on/off setting.

Caution
� The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use. � Frequent use of the backligfht shortens the battery life. � The watch emits an audible sound whenever the display is illuminated. This is because the EL light vibrates slightly when lit. It does not indicate malfunction of the watch.

C

D

Longitude

6. While the GMT differential is selected (flashing), press D to increase the value. Holding down D changes the

Warning!
� Never try to read your watch when mountain climbing or hiking in areas that are dark or in areas with poor footing. Doing so is dangerous and can result in serious personal injury. � Never try to read your watch when running where there is the danger of accidents, especially in locations where there might be vehicular or pedestrian traffic. Doing so is dangerous and can result in serious personal injury. � Never try to read your watch when riding on a bicycle or when operating a motorcycle or any other motor vehicle. Doing so is dangerous and can result in a traffic accident and serious personal injury. � When you are wearing the watch, make sure that its auto light switch function is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.

current selection at high speed. 7. While Longitude/Latitude is selected (flashing), press D to change the value of longitude or B to change the value of latitude. Holding down either button changes the corresponding setting at high speed. < Longitude >
Press D 179°W 0°E 180°E 65°S

< Latitude >
Press B 0°N 65°N

8. After you set the location data, press A to return to the Timekeeping Display.

Important
After you change a setting in the above procedure, the watch needs a bit of time to calculate certain information. During this calculation, the patterns in the graphic display move at high speed. Wait until these display stop moving before you try to input any further data.

�6�