SHARP EL-6985
Instrukcja Serwisowa

PARTS LIST
No. 1 2 3 PARTS CODE 0MYMSCRWF21300 0MYM6053S266A0 0MYM6985680100 0MYM6985680200 PRICE RANK AD AF AE AE N N N NEW MARK PART RANK C D D D Screw Battery cover Manual (ENGLISH) Manual (SPANISH) 7. Set the clock. DESCRIPTION (for Battery cover)

Battery Replacement
Battery used Type Lithium battery Model CR2032 Quantity 1

When removing the battery, use the side opposite the curved corner of the battery holder cover.

� Improper replacement of the battery may change or lose the memory contents. � Be sure to write down any important information stored in the memory before replacing the battery. � Make sure the power is turned off before replacing the battery. � Do not use a metallic object to pry out the battery. The Organizer will be subjected to an electrical shock and all the memory contents will be cleared. � Complete the replacement of the battery within 1 minute, otherwise all the memory contents may be cleared. � Do not press pleted.
OFF

Fig. 1
Note: Make sure to confirm all settings are set correctly after replacing the batteries. Note) Packing form Form Blister SPEC U1U Country SEC

until the battery replacement procedure is com-

CAUTION FOR BATTERY REPLACEMENT
(Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. "BATTERY DISPOSAL" CONTAINS MANGANESE DIOXIDE LITHIUM BATTERY. MUST BE DISPOSED OF PROPERLY. REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR STATE ENVIRONMENTAL AGENCIES FOR INFORMATIN ON RECYCLING AND DISPOSAL OPTIONS. (Finnish) VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (French) ATTENTION Il y a danger d'explosion s' il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d'un type recommandé par le constructeur. Mettre au rébut les batteries usagées conformément aux instructions du fabricant. (Swedish) VARNING Explosionsfare vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

ON

1. Precautions Since improper use of the battery may cause leakage or explosion, strictly observe the following instructions. � Insert the battery with positive side (+) correctly facing up. � Never throw the battery into a fire because it might explode. � Keep the battery out of the reach of children. Because the battery in the Organizer was installed at the factory, it may become depleted before the specified expiration time is reached. 2. Battery replacement When �LOW BATTERY� is displayed, immediately replace the batteries with new ones. Under the low battery condition, followings may occur. � New data entry and editing of existing data may not be performed in some modes. � Clock and other settings may not be made. � The alarm may not sound. Continued use of the Organizer with low batteries can alter or clear the memory contents. 1. Press
OFF

ON

to turn the power off.

2. Loosen the screw and remove the battery holder cover on the back of the unit. 3. Remove the exhausted battery by prying it out from the holder with the corner of the holder cover. (Fig. 1) 4. Install a new battery with the positive side (+) facing up into the holder. 5. Replace the holder cover and secure it with the screw. 6. Press
OFF

COPYRIGHT © 2002 BY SHARP CORPORATION
All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted. In any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

ON

to turn the power on.

� If nothing appears on the display, press the RESET switch and press . � Do not press the memory contents. . Pressing clears all

SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center

2002 May Printed in Japan t