EMERSON EWD2004
Instrukcja Obsługi

Preset for Use
Turn on the unit for the first time
VCR

To Preset the Channel Again
1) Press the MENU button until the main menu appears. 2) Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B button. 3) Select "AUTO SET UP" by pressing the K or L button. Then, press the B button. After scanning, the tuner stops on the lowest memorized channel.

4
or

CLOCK SET MONTH DAY 03 / 15 HOUR MINUTE �� : �� YEAR 2004 AM/PM ��

VCR

1
Turn on the TV and set it to channel 3.
� If channel 3 is already occupied for broadcasting, see�RF Output Channel� section.

Select the current year

To Change the On-Screen Language
1) Press the MENU button until the main menu appears. 2) Select "LANGUAGE SELECT" by pressing the K or L button. Then, press the B
LANGUAGE SELECT B ENGLISH or FRANCAIS ESPA�OL [ON]

5
or

CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : �� AM/PM ��

2

POWER

Remote Control

TV Screen

button. 3) Select "ENGLISH" , "FRANCAIS" or "ESPA�OL" by pressing the K or L button. Then, press the CLEAR/C.RESET button.

Select the current hour

Setup
3
YES

Hint
CH 01

6
or

� If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC. IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button.

CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : 40 AM/PM ��

AUTO SET UP

Clock Set Up
VCR

Select the current minute

VCR
Do you connect the cable from the cable box or the satellite box to the DVD/VCR�s ANT IN jack?

1

MENU

Yes Press the MENU
button to exit
� Refer to �Hint for Cable Box or Satellite Box� section on page 6.
or

TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT

-MENU-

7
or

CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : 40 AM/PM P M AM B PM

NO

Please wait for a few minutes. After scanning...
� The tuner stops on the lowest memorized channel. � You can select only the channels memorized in this unit by using the CHANNEL buttons. � If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then press the B button once again.

No No

� If the clock is not set, the CLOCK SET screen appears when you press the MENU button. In this case, go to step [2].

Select �AM� or �PM�

8 2
or CLOCK SET MONTH DAY 03 / �� HOUR MINUTE �� : �� YEAR ���� AM/PM ��

To exit the CLOCK SET screen.

Hint
� Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds. Select the current month

Hint
� To go back one step, press the s button (during the steps [2] to [7].) � Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.

To Select a Channel
You can select a channel by directly entering channel using the Number buttons on the remote control. Notes for using the Number buttons: � When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1,1,7) � You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

3
or

CLOCK SET MONTH DAY 03 / 15 HOUR MINUTE �� : �� YEAR ���� AM/PM ��

Select the current day

� 10 �

EN