|
|
|
Kto jest w sklepie?
Sklep przegląda 5690 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
RF Output Channel
If channel 3 is already occupied for broadcasting, Hint 1) Set your TV to channel 4. 2) Insert a pre-recorded tape into the VCR. � The RF output channel may not change when you adjust 3) Press the PLAY button once. tracking during playback. In 4) After a few seconds, press the PLAY button on the VCR for 3 seconds. this case, stop the playback, � The RF output channel will change to channel 4 from channel 3 and you will and start the playback again. After that, press the PLAY butsee a playback picture. ton on the VCR for 3 seconds � When a picture does not appear on the TV screen, repeat step [4]. again. 5) Press the STOP button to stop playback.
Owner�s Manual Video Cassette Recorder
If you need additional operating assistance after reading this owner�s manual or to order replacement accessories, please call
TOLL FREE : 1-800-256-2487
EWV404
Basic VCR/TV Connection
Cable Signal or Antenna (Back of TV) Cable Signal or
or visit our web site at http://www.funai-corp.com
1. Before using your VCR
Antenna (Back of VCR) (Back of TV)
Stereo TV Connection
You can use the AUDIO OUT jack and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV�s owner�s manual.
VIDEO OUT AUDIO OUT
VIDEO IN
AUDIO IN L R
ANT AUDIO
IN
OUT
IN
OUT
Audio/Video Cables
(not supplied)
L R
VIDEO
ANT IN
2
Disconnect Connect
ANT IN OUT
3
Connect
1
Connect
OUT
(Back of TV)
(Back of VCR)
Front & Rear Terminals
RF Cable (supplied)
4
Plug the AC power cords of the VCR and TV into the AC outlets.
Hint for Cable Box or Satellite Box
Connection A
(Cable box or Satellite box)
IN OUT
OUT ANT IN
AUDIO OUT jack Connect the audio cableVCR, aaudio in jack of a camcorder, another to the stereo amplifier, or an audio system.
AUDIO IN jack Connect the audio cable fromVCR,audio out jack of a camcorder, another the or an audio source.
ANT IN
(Back of VCR)
Connection B
ANT IN
(Back of VCR) (Cable box or Satellite box)
E
ANT IN AUDIO OUT IN
ANT IN jack Connect your antenna or cable box. ANT OUT jack Connect the RF cable (supplied) to the antenna input jack on your TV.
AUDIO OUT IN
Cable Signal
RF Cable (supplied)
E
Cable Signal
OUT
IN
OUT
(Back of TV)
RF Cable (supplied)
RF Cable
(Back of TV)
VIDEO
OUT
OUT
VIDEO
Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box. � While you are recording, only the recorded channel can be viewed. To select channels of the cable box or satellite box 1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box). � If you use the channel 4, you need to change the VCR�s RF output to channel 4. Refer to �RF Output Channel�. 2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1). 3) At the cable box or satellite box, select the channel you want to view or record.
Select this connection when you want to change channels on the VCR. With this connection, you may watch one channel while recording another. � You may not view or record a scrambled channel. To select channels of the cable box or satellite box 1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the VCR�s RF output channel.) � Refer to �RF Output Channel�. 2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box. 3)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button .The POWER and VCR/TV indicators on the front panel will light on. Then, select the channel you want to view or record. To play back a tape Follow the steps 1) to 2) above. Then, play back a tape. � Refer to �Playback� on page 5. To view one channel while recording another 1)While you are recording on the VCR, press the VCR/TV button so that the VCR/TV indicator disappears on the VCR. 2)At the cable box or satellite box, select the channel you want to view. -
VIDEO OUT jack Connect the video cable to the video in jack of a camcorder, another VCR, or a TV.
POWER VCR/TV TAPE IN TIMER REC
VIDEO
AUDIO
POWER
CHANNEL
MENU
VIDEO IN jack Connect the video cable from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.).
Supplied Accessory
� Remote control (NA372UD) with Two AA batteries � RF Cable � Owner�s Manual (WPZ0901TM002) (0VMN04033)
Installing the Batteries for the Remote Control
Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control.
Printed in China 10VMN04033 / HF331UD �����
|
|
|
> |
|
