PHILIPS FW-C85/37
Instrukcja Obsługi

23

RECORDING
4 Press DUB (HSD) once for normal speed dubbing or twice (within 2 seconds) for high speed dubbing. � "NORMAL" (normal speed) or "FAST" (high speed) will be displayed, followed by "DUB" with "! or @" scrolling left or right depending on the tape side selected. � The HSD appears on the display during high speed dubbing. � Dubbing will start immediately. � The REC starts flashing. 5 Press � to stop dubbing. Notes: � Only å mode is available during dubbing. � At the end of side A, flip the tapes to side B and repeat the procedure. � Dubbing of tapes is only possible from tape deck 1 to tape deck 2. � To ensure good dubbing, use tapes of the same length. � During high speed dubbing in Tape mode, the sound is reduced to a low volume. � You can listen to another source while dubbing.

CLOCK
STANDBY ON

CD Synchro Start Recording
1 Load a blank tape into tape deck 2 and a disc into a disc tray. 2 Press CD to select CD mode. � You can program the tracks in the order you want them to be recorded (see Programming Tracks). If not, select the disc by pressing CD 1�2�3 and the tracks are recorded according to the order on the selected disc. 3 Press RECORD to start recording. � The REC starts flashing. � CD will start playback automatically. 4 Press � to stop recording.

MINI HIFI SYSTEM

POWER SAVE

IR SENSOR

CD 1�2�3 C1 � 2 � 3 CD
C VE
BASS/T
R EBL

FM�AM BAND TUNER
STOP�CLEAR

TAPE 1�2 TAPE
PLAY PAUSE v

CDR/DVD AUX CDR
SIDE NEXT PREV PRESET v

SEARCH�TUNING
E

VOLUME

C
D S

PERS ON AL

PROG

CLOCK/ TIMER

DIM

A. REV

DUB (HSD)

RECORD

BASS

TREBLE

PLUS

TECHNOLOGY

wOOx

LEVEL

View Clock
You can view the clock (if it is set) if the system is in Standby mode or when any sound source is selected (CD, TUNER, etc.). The clock will be displayed for about seven seconds. � Press CLOCK/TIMER briefly (or CLOCK on the remote control). � "PM 10:38 or 22:38" (the current time) will be displayed depending on whether you have selected 12- or 24-hour mode. � "--:--" will be displayed if the clock is not set. Note: � When the system goes into low power standby mode, the clock setting will not be displayed.

Clock Setting
The clock can be set in either 12- or 24-hour mode, e.g. "AM 12:00" or "00:00". Before setting the clock, you must be in the View Clock mode. 1 Press CLOCK/TIMER to select clock mode. 2 Press PROG (on the system only) to select 12- and 24- hour mode. � If 12-hour mode is selected, "AM 12:00" starts flashing. � If 24-hour mode is selected, "00:00" starts flashing. 3 Set the hour with à or á on the system. 4 Set the minute with í or ë on the system.

One Touch Recording
� For One Touch Recording, as soon as you press RECORD, the current source (CD, TUNER or AUX) will be recorded on tape deck 2. 1 Load a blank tape in tape deck 2. 2 Press RECORD to start recording. � The REC starts flashing. 3 Press � to stop recording. Note: � When you press RECORD while in TAPE mode, "SELECT SOURCE" will be displayed. One Touch Recording is not possible in TAPE mode.

pg 01-28/C85/37-Eng

23

2/16/00, 9:03 AM

3139 116 19591 (ENG)