PHILIPS FWR7
Instrukcja Serwisowa

Brief Operating Instructions

INSTALLATION
Power
The type plate is located on the rear of the unit.
1 Check whether the power voltage as shown on the type plate corresponds to your local power voltage. If it does not, consult your dealer or service organization. 2

INSTALLATION
English
CD PLAYER
DIGITAL DIGITAL IN OUT SUBWOOFER OUT AUX IN LINE OUT

Antenna connections
AM antenna The supplied loop antenna is for indoor use only. 1 Fit the plug of the loop antenna to AM AERIAL as shown below. 2 Position the antenna as far as possible from a TV, VCR or other radiation sources. 3 Turn the antenna for optimum reception.
AM AERIAL
AC MAINS ~

English

Make sure all connections have been made before switching on the power supply.

SUBWOOFER

L

R

L

R

3 Connect the supplied power cable to AC MAINS ~ and to the power outlet. This switches on the power supply.

AM AERIAL

FM AERIAL 300 �

For optimal performance use only the original power cable.
When the unit is switched to standby, it is still consuming some power. To disconnect the unit from the power completely, remove the power cable from the power outlet.

TAPE RECORDER

CD RECORDER

SPEAKERS 6� FRONT

L

R

To avoid overheating of the set, a safety circuit has been built in. Therefore, your unit may disconnect under extreme conditions. If this happens, switch the unit off and let it cool down before reusing it.

FM antenna The supplied wire antenna can only be used to receive nearby stations. For better reception we recommend using a cable antenna system or an outdoor antenna. 1 Open the FM AERIAL 300 � click-fits by pushing the lever down as shown below. 2 Insert each wire of the antenna into one hole. 3 Close the click-fits using the lever. 4 Move the antenna in different positions for optimum reception.
FM AERIAL 300 � FM 0� AERIAL 30

Speaker connections
The speaker connections are click-fit connectors. Use them as shown below.

Analog audio connections
AUX IN L/R It is possible to use an additional appliance, e.g. tape recorder, TV or VCR, with the unit. 1 Insert the red plug of a cinch cable to the red jack AUX IN R and insert the white plug to the white jack AUX IN L. 2 Connect the other end of the cinch cable to the audio outputs of the additional appliance. 3 Press DIGITAL / ANALOG AUX repeatedly to select the analog input for the appliance. yAUX Analog is displayed.

Digital audio connections
DIGITAL IN You can use this coaxial input for recordings from any digital audio equipment with a digital coaxial output e.g. CD player or DVD player. 1 Use a coaxial cable to connect the coaxial output of the additional appliance with DIGITAL IN on the unit. 2 Press DIGITAL / ANALOG AUX repeatedly to select the digital input for the appliance. yAUX Digital is displayed. 3 Operate your appliance as usual. DIGITAL OUT You can use this coaxial output for recordings on any digital audio equipment with a digital coaxial input e.g. CD recorder. � Use a coaxial cable to connect the coaxial input of the additional appliance with DIGITAL OUT on the unit and operate your appliance as usual.

2-5

1 Connect the colored (or marked) wire to the red terminal and the black (or unmarked) wire to the black terminal. 2 Connect: � Left speaker to L (red and black) � Right speaker to R (red and black)

The unit complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

4 Operate your appliance as usual and adjust volume and sound with the unit.

Note: It is not possible to connect a turntable directly to AUX IN L/R. If you wish to use a turntable with the unit, you have to connect an amplifier to AUX IN L/R on the unit. Then connect the turntable to the amplifier.
LINE OUT L/R You can use these outputs for playback or recording on any analog audio equipment e.g. amplifier or tape recorder. � Use a cinch cable to connect the analog audio inputs of the additional appliance with LINE OUT L/R on the unit and operate your appliance as usual.

Connecting a subwoofer
A subwoofer can be used to enhance the bass performance of your unit dramatically. 1 Use a cinch cable to connect the input of the subwoofer with SUBWOOFER OUT at the unit. 2 Follow the instructions supplied with the subwoofer.

10

11