Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Tekstowy podgląd strony 2 (kliknij aby zobaczyć)
PREPARATIONS
1. Power Supply for Camera
Prepare a regulated DC power supply which can supply DC 12 V ±10 % DC 465 mA or more current and rated CLASS 2.
SPECIFICATIONS
3. Switch Covers Removal
Caution: The following preparation should be made by qualified service personnel or system installers. For setting the Rear Panel Switch No.1 to 8, remove the switch cover fixing screw on the rear panel as shown below. Pick-up Device : Image Size : Synchronization : Inter Line Transfer type CCD with 768 (H) x 494 (V) pixels. 2/3� (7.95 (H) x 6.45 (V) mm) Full non interlace (1/60 s) Internal or External (Selectable Automatically) Internal : Built-in sync generator External : 4.0 V[p-p]/75 � Horizontal drive and Vertical drive pulses External signal (4.0 V[p-p]/75 �, negative) supplied to EXT VD IN connector can be used as reset signal 500 lines at center 5 lx (0.5 foot-candles), (F1.4, Gain (+6 dB) , γ OFF) 1.0 0/+6 dB 9-step (1/100 s to 1/30 000 s) at normal 5-step (1/2 000 s to 1/30 000 s) at Shutter Trigger C-Mount 7 G (10 Hz - 150 Hz) (2 hours each for three axes) 80 G (IEC 68) *IEC=International Electronical Technical Commission DC + 12 V, 465 mA �10�C - +50�C (14�F - 122�F) 45(W) x 45(H) x 120(D) mm [1-25/32�(W) x 1-25/32�(H) x 4-23/32�(D)] 270 g (0.6 lbs.) (Camera Only)
2. Lenses
Be sure to use the optional manual iris lens having the following items. Focus : Adjustable Lens Weight : Less than 300 g (0.66 lbs.) Note: If the lens is heavier than 300 g (0.66 lbs.), both the lens and the camera should be secured by using the supporter. Mount : C-mount The protrusion at the rear of the lens should be as shown in the illustration.
External Reset : Horizontal Resolution : Minimum Illumination : Gamma : Gain Selection : Electronic Shutter : Lens Mount : Vibration Resistance : Shock Resistance : Power Source : Ambient Temperature : Dimensions : Weight :
Remove this screw
VIDEO
Dimensions and weight indicated are approximate values. Specifications are subject to change without notice.
Less than 7.5 mm (1/2�)
SYSTEM CONNECTIONS
Caution: Keep the power switches of all units to OFF before connections. 1. Connect the optional camera cable GP-CA34 between the connector of this camera and the 12 V DC Class 2 power supply(not provided as an accessory). 2. Connect the video connector of the GP-CA34 to the Frame Grabber.
OPTIONAL ACCESSORIES
Camera Cable GP-CA34 GP-CA33 GP-CA59 GP-CA60
Camera GP-CA34 Video input of Frame Grabber
12V DC Power Supply HD IN VD/V reset
Caution: Use a 12 V DC Class 2 Power Supply only
EXTERNAL SYNCHRONIZATION
Full non interlace The GP-MF852PT works in full non interlace mode when external HD/VD signal is supplied to pin-6 and pin-7 of the camera connector (12-pin). Notes: � If the picture appears disturbed, be sure to match the phases of falling edges of the external HD/VD. � Normal monitor cannot display the picture from this camera. To display the picture, synchronize the camera and multiscan monitor from external HD/VD.
