|
|
|
Kto jest w sklepie?
Sklep przegląda 5962 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
 ;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
DISASSEMBLY ADVICE DIAL 15 PUMP 8 HOSE 14 HANDLE 6
remove remove remove remove remove remove remove remove unplug remove remove remove remove remove STEAM KNOB 3 DIAL 15 SCREW A NOSE 7 SCREW B INLAY 1 SCREW C 2x LAMP 17 TERM. SOCKET 4.1 HOSE 11 TERM.SOCKET 4.2 HANDLE 6 NUT 9 PLATE 101
INLAY 1 HOSE 11 SWIVEL 12
remove CAPS 20 4x remove SCREW E 4x remove HOUSING 33 remove screw G 2x remove screw F remove wiring / HOSE remove remove remove remove unplug SCREW A INLAY 1 SCREW C 2x LAMP 17 TERM.SOCKET 4.1
STEAM KNOB 3
SOLE PLATE 10.1 SKIRT 10.2 THERMOSTAT 10.3
remove NOSE 7 remove SCREW B remove SCREW A remove INLAY 1 remove SCREW C remove LAMP 17 unplug TERM.SOCKET 4.1 remove HOSE 11 remove TERM.SOCKET 4.2 remove HANDLE 6 remove THERM.BUSH 19 remove screw D 2x (item 10.2 / 10.3 only)
NOSE COVER 7
To adjust the thermostat. The sole plate is completely cooled off. Tum the bracket to position � A � Then turn bracket a quarter turn clockwise to position � B � You will hear a � CLICK � Save the screw with loctite or the like If in position � B � no � CLICK � is heard, adjust the thermostat with the screw inside the thermostat shaft. Turn the screw in such a way that a � CLICK � is heard in pos. � B � Save the screw with loctite or the like. N.B. This procedure is applicable if only the thermostat is replaced. Thermostats, see 10.1 have already been adjusted.
CORDSET 24 SWITCH 2 SWITCH KNOB 5
remove SCREW A remove INLAY
SIEVE 26 SEALING RING 23 SEALING RING 25 SWITCH 22
remove CAP 20 4x remove SCREW E 4x remove HOUSING 33
NOTES: After the product has been repaired, it should function properly and has to meet the safety requirements as laid down and officially established at this moment. N.B. Parts, with numbers from 100 upwards, cannot be ordered separately. Item 27 consists of one pump, a straight tube and a plug. Products produced before week 9216 have 2 pumps. If one of them needs to be replaced, proceed as follows : - Remove 2 existing pumps and the T-connecting tube. - Assemble the new pump and the corresponding straight tube only. The pump has to be assembled at the position indicated in exploded view of this manual. - Close the remaining hole in the water tank with the plug. - Cut the 2 remaining electric connecting wires and insulate the ends with insulation tape.
SWITCH PLATE 29 SWITCH 30 PUMP 27 ONE WAY VALVE 28 LAMP 17 LAMP COVER 18
remove remove remove remove remove remove remove unplug remove remove remove DIAL 15 SCREW A NOSE 7 SCREW B INLAY 1 SCREW C 2x LAMP 17 TERM.SOCKET 4.1 HOSE 11 TERM.SOCKET 4.2 HANDLE 6 remove CAP 20 4x remove SCREW E 4x remove HOUSING 33 remove SCREW F remove wiring HOSE 11 remove wiring PUMP 27 remove wiring CORDSET 24
PCS 89 575
|
|
|
> |
|
