PHILIPS HQ5715/22
Instrukcja Obsługi

ENGLISH
Important Read these instructions for use carefully before using the appliance and save them for future reference. , Use and store the appliance at a temperature between 5°C and 35°C. , The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. (Fig. 1) Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. , Remove the batteries if you are not going to use the appliance for a month or more. Preparing for use The appliance runs on two R6 AA 1.5-volt batteries. We strongly advise you to use Philips LR6 alkaline batteries. They supply suf�cient energy for approx. 60 minutes of shaving. Inserting batteries

The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the appliance. Never rinse the shaver when the battery compartment is open. Always make sure the cap of the battery compartment is in place and properly locked before you start rinsing the shaver. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Every day: shaving unit and hair chamber

2 Remove the shaving unit. (Fig. 9) 3 Turn the wheel anticlockwise (1)
(Fig. 13) and remove the retaining frame (2).

Frequently asked questions Question Why doesn�t the shaver shave as well as it used to? Answer You may not have cleaned the appliance properly. Clean the shaving heads thoroughly see chapter �Cleaning and maintenance�). Long hairs may be obstructing the shaving heads. Clean the cutters and guards properly with the brush supplied (see chapter �Cleaning and maintenance�). The shaving heads may be damaged or worn. Replace the shaving heads (see chapter �Replacement�). The batteries may be running low. Replace the batteries (see chapter �Preparing for use�). Why doesn�t the shaver switch on when I push the on/off button upwards? The batteries may be empty. Replace the batteries (see chapter �Preparing for use�).

4 Remove the shaving heads from the
shaving unit and replace them with new ones. (Fig. 14)

5 Put the retaining frame back into
the shaving unit, press the wheel and turn it clockwise.

6 Put the shaving unit back onto the
shaver. Accessories The following accessories are available: - HQ64 Philips Double Action Super Lift & Cut Shaving Heads (HQ5715) - HQ54 Philips Double Action Lift & Cut Shaving Heads (HQ5710/HQ5705) - HQ110 Philips Shaving Head Cleaning Spray Environment , Do not throw the appliance away with the normal household waste at the end of its life, but hand it in at an of�cial collection point for recycling. By doing this you will help to preserve the environment. (Fig. 18) , Batteries contain substances that may pollute the environment. Do not throw empty batteries away with the normal household waste, but hand them in at an of�cial collection point for batteries. Always remove the batteries before discarding the appliance and handing it in at an of�cial collection point. Guarantee & service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you will �nd its phone number in the worldwide guarantee lea�et). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

1 Switch the shaver off. 2 Remove the shaving unit. (Fig. 9) 3 Rinse the outside of the shaving unit
under a hot tap for some time. (Fig. 10)

4 Rinse the inside of the shaving unit
under a hot tap for some time. (Fig. 11)

1 Unlock the cap of the battery
compartment. (Fig. 2)

5 Rinse the hair chamber under a hot
tap for some time. (Fig. 12)

2 Remove the cap of the battery
compartment. (Fig. 3)

6 Put the shaving unit back onto the
shaver and shake off excess water. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads. Every six months: shaving heads

3 Put two batteries in the battery
compartment. (Fig. 4) Make sure your hands and the appliance are dry when you insert the batteries. , Make sure the + and - poles of the batteries point in the right direction The appliance does not work if the batteries have been placed incorrectly.

1 Switch the shaver off. 2 Remove the shaving unit. (Fig. 9) 3 Turn the wheel anticlockwise (1)
and remove the retaining frame (2). (Fig. 13)

4 Push the cap of the battery
compartment back onto the appliance.

4 Remove the shaving heads from the
shaving unit. (Fig. 14)

5 Lock the cap of the battery
compartment. (Fig. 5) Optimising the lifetime of the battery To avoid damage due to battery leakage: - Remove the batteries if you are not going to use the appliance for a month or more. - Do not leave empty batteries in the appliance. Using the appliance

5 Remove the guard from the cutter.
(Fig. 15)

6 Clean the cutters with the shortbristled side of the brush. (Fig. 16) Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored.

1 Remove the protection cap. 2 Switch the shaver on by pushing the
on/off slide upwards. (Fig. 6)

7 Brush the guard. (Fig. 17) 8 Put the shaving heads back into the
shaving unit. Put the retaining frame back into the shaving unit, press the wheel and turn it clockwise.

3 Move the shaving heads quickly over
your skin, making both straight and circular movements. (Fig. 7) Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.

9 Put the shaving unit back onto the
shaver. Storage , Put the protection cap on the shaver to prevent damage. (Fig. 8) Replacement Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ64 Philips Double Action Super Lift & Cut Shaving Heads (HQ5715) or HQ54 Philips Double Action Lift & Cut Shaving Heads (HQ5710,5705).

4 Switch the shaver off by pushing the
on/off slide downwards.

5 Put the protection cap on the shaver
every time you have used it, to prevent damage. (Fig. 8) Cleaning Regular cleaning guarantees better shaving performance. 4222 002 47201

1 Switch the shaver off.
2/9