JVC HR-S9400E
Instrukcja Obsługi

EN

29

ACCESS SHOWVIEW PROGRAM SCREEN

NOTE:

3

Press OK, and the SHOWVIEW Program screen appears (if you�re just starting out, �P1� appears).

� P1 � SHOWVIEW 123456789 START STOP 21:00 = 22:00 SP DATE 25.12 : OK ON TV PROG 1 ARD

To Delay The Stop Time . . . . . . press ADD TIME (NUMBER Key "5") after pressing OK in step 3. Each time you press, the Stop time is delayed by 5 minutes (meaning that 5 minutes of recording time is added). You can easily compensate for anticipated programme schedule delays this way. To Timer-Record Weekly Or Daily Serials . . . . . . after pressing OK in step 3, press WEEKLY (NUMBER key �9�) for weekly serials or DAILY (NUMBER key �8�) for daily
serials (Monday�Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear. You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes ( pg. 32).

The display panel shows the programme start time. Pressing PROG CHECK changes the display to the programme stop time, then the date and channel position.
SP

IMPORTANT
Be sure to confirm the setting of PDC/VPS recording. � If " ON" is displayed on the screen or " " is lit on the display panel, PDC/VPS is set to ON. � If " OFF" is displayed on the screen or " " is not lit on the display panel, PDC/VPS is set to OFF. To change the setting, press : PDC/VPS (NUMBER key "7"). "PDC/VPS Recording" on page 33. � Make sure the channel position number you wish to record is displayed; if not, see "SHOWVIEW Setup" on page 12 and set the Guide Program number for that SHOWVIEW number correctly. � If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press CANCEL to backspace and input a valid SHOWVIEW number. � If "ERROR=GUIDE PROG" appears on the screen, see "ATTENTION � Regarding Guide Program Number Set" in the right column. � If you are using the Illumi-Guide feature, OK blinks.

Satellite Tuner Users
To timer-record a satellite broadcast using SHOWVIEW: � Before you start step 1, be sure to set the recorder's input mode to "AUX2" ( pg. 35). Do NOT change the input mode until the selected programme has been timerrecorded. � Before the selected programme begins, select the appropriate channel on the satellite tuner, and then set the tuner's timer. If your satellite tuner does not have a timer, leave the unit's power on.

ATTENTION
Regarding Guide Program Number Set
"ERROR=GUIDE PROG" appears after performing step 3 on the previous page if the Guide Program number for the SHOWVIEW number you entered has not been set. � If the recorder is in the stop or rewind or fast-forward mode, the following screen will appear with "� �" under "TV PROG" blinking. � Press the NUMBER keys or PUSH JOG %� to input the channel position number you recorder receives that station on, then press OK.
GUIDE PROG SET GUIDE PROG 2 TV PROG ��

SET TAPE SPEED
Press SP/LP ( ) to set the tape speed.

4
RETURN TO NORMAL SCREEN

5 6

Press OK. � Repeat steps 1 � 5 for each additional programme.

ENGAGE RECORDER�S TIMER MODE
Press TIMER. The recorder turns off automatically.

� Press MENU, then try again from step 1. � If the recorder is in a mode other than the above mentioned modes, press MENU first and input the correct Guide Program number for that SHOWVIEW number ( pg. 12, "SHOWVIEW Setup"), then try again from step 1.

[5�] = [MENU] : EXIT

(Ex.) To timer-record a ZDF programme with SHOWVIEW * If your recorder receives ZDF on the channel position 2, press OK after entering "2".