|
|
|
Kto jest w sklepie?
Sklep przegląda 5817 gości i
3 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
KMD-PS971R/X92
TEST MODE
(10) Simplified security code clear procedure (KMD-X92 only) 1. During the code request mode, while holding the "DISP" key depressed, press and hold the volume "UP" key for 3 seconds (so that "----" disappears). 2. Enter "KCAR" from the remote control unit. Press numeric key "5" 2 times and press the track "UP" key (to enter "K"). Press numeric key "2" 3 times and press the track "UP" key (to enter "C"). Press numeric key "2" 1 time and press the track "UP" key (to enter "A"). and press the track "UP" key (to enter "R"). 3. The security is canceled and the set enters the tuner mode. (11) MASK key writing procedure (When the EEPROM is in the initial status) 1. While holding the "FM" and preset "6" keys depressed, press "RESET" to enter the test mode. 2. Press and hold the "AUDIO" key for 1 second to enter the menu mode. 3. Press the "FM" or "AM" key to select "Mask key". 4. Press the track "UP/DOWN" key shortly so that "TRANSMIT1" is displayed. 5. Point the MASK key to the light sensor and press and hold the key for more than 0.5 second. 6. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 0.5 second. Note that the first and second counter codes are not compared at this time. 7. The writing operation is completed when "APPROVED" is displayed. At this time, the demonstration mode is set and the test mode is canceled. (Note) Leaving the unit for more than 30 minutes without writing the code causes an error and turns power off. (12) Procedure for canceling the MASK key request (when the unit is reset or the back-up power is turned off while the MASK key is enabled) 1. When the power is supplied and the unit is switched on, "TRANSMIT1" is displayed and the MASK key request mode starts. 2. Point the MASK key toward the light sensor and press and hold for more than 3 seconds (until the level indicator indicates the full condition). 3. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 3 seconds. If "TRANSMIT1" is displayed now, go back to step "2" and restart from there again. 4. When "APPROVED" is displayed, the MASK key is enabled and the set is turned on. (13) Procedure for MASK key initialization 1. While holding the "FM" and preset "6" keys, press "RESET" to enter the test mode. 2. "TRANSMIT1" is displayed and the MASK key request mode starts. At this time, the display shows "* *" in place of "[ ]". 3. Press the MASK key canceling remote control for more than 3 seconds. 4. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 3 seconds. 5. When "APPROVED" is displayed, the MASK key is canceled, the demonstration mode is set, the test mode is canceled. (14) MASK key all-clear procedure 1. While holding the "FM" and preset "6" keys, press "RESET" to enter the test mode. 2. Press and hold the "AUDIO" key for more than 1 second to enter the menu mode. 3. Press the Track "UP/DOWN" key to select "Mask key". 7 Press numeric key "7" 2 times
|
|
|
> |
|
