CASIO LWE11-1A
Instrukcja Obsługi

USER�S GUIDE 2482/2600
General Guide
� Press B to change from mode to mode. Timekeeping Mode Alarm Mode � After you perform an operation in any mode, pressing B returns to the Timekeeping Mode. � In any mode, press A to illuminate the display. Stopwatch Mode Time Setting Mode

Press

.

[Modules 2482, 2600]

Timekeeping Mode
PM indicator Day of the week Day

Stopwatch Mode
� In the Timekeeping Mode, press C to switch � between 12-hour format, the P (PM) indicator appears to With the the 12-hour and 24-hour formats. the left of the hour digits for times in the range of noon to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the range of midnight to 11:59 a.m. � With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24 indicator. � Day of the week is displayed as follows. SU: Sunday TU: Tuesday TH: Thursday SA: Saturday MO: Monday WE: Wednesday F R : Friday
Mode indicator Minutes Seconds

The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.

Hour

Minutes

1/100 second

Seconds

Split time indicator

Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. � The electro-luminescent panel that provides illumination loses power after very long use. � The illumination provided by the backlight may be hard to see when viewed under direct sunlight. � The watch may emit an audible sound whenever the display is illuminated. This is due to vibration of the EL panel used for illumination, and does not indicate malfunction. � Frequent use of the backlight shortens the battery life.

(a) Elapsed time measurement Start Stop Re-start Stop Clear

(b) Split time measurement Start Split
(SPL displayed)

Split release

Stop

Clear

(c) Split time and 1st-2nd place times Start Split
First runner finishes. Display time of first runner.

Stop
Second runner finishes.

Split release
Display time of second runner.

Clear

Alarm Mode
Mode indicator Hour Minutes

When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is turned on, the watch beeps every hour on the hour.

� Pressing A also illuminates the display.

To set the alarm time
1. Hold down A while in the Alarm Mode until the hour digits start to flash on the display. The hour digits flash because they are selected. � This operation automatically turns on the alarm.
Hourly time signal on indicator Alarm on indicator

Time Setting Mode
PM indicator Day of the week Day

To set the time and date
1. Use B to enter the Time Setting Mode. � The second�s digits flash because they are selected. 2. Press A to change the selection in the following sequence. � Pressing A also illuminates the display.

Seconds Day of week

Hour Day

Minutes Month

2. Press A to change the selection in the following sequence. � Pressing A also illuminates the display.

Hour

Minutes
Hour Minutes Seconds

Normal Alarm Mode (No digit flashes)
3. Press C to increase the selected digits. Holding down C changes the number at high speed. � The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. � When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon (P). 4. After you set the alarm time, press A to return to the Alarm Mode.

To stop the alarm
Press A to stop the alarm after it starts to sound.

3. While the second�s digits are selected (flashing), press C to reset the seconds to �00�. If you press C while the second�s count is in the range of 30 to 59, the seconds are reset to �00� and 1 is added to the minutes. If the second�s count is in the range of 00 to 29, the minute�s count is unchanged. 4. While any other digits (besides seconds) are selected (flashing), press C to increase the number. While the day of the week is selected, pressing C advances to the next day. Holding down C changes the current selection at high speed. 5. After you set the time and date, press B to return to the Timekeeping Mode. � If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically.

To switch the Daily Alarm and Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence. [Alarm on Indicator/Hourly Time Signal on Indicator]

Both on

Both off

Daily Alarm only

Hourly Time Signal only

To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.

1