PHILIPS MCM108B/96
Instrukcja Obsługi

Radio Reception

Other Connection
Helpful hints: To improve radio reception: � For FM, extend coil antenna at the back of the unit fully for optimum reception.

Clock/Timer
4 5
M I C R O S Y S T E M M C M10 8

Press ¡1 / 2� to set the hours. Press TIMER again. � The clock digits for the minutes flash. Press ¡1 / 2� to set the minutes. Press TIMER to confirm the time. � The timer is now set and actiated. Notes: - If source CD is selected and no disc is in the CD tray or the disc has an error, TUNER will be selected automatically. - At the set time of wake up, the set will turn on at volume level 12. To activate and deactivate timer

iR

Listening to an external source
You can listen to the sound of the connected external device through your system�s speakers. Select AUX source. Use a line-in cable (not supplied) to connect MCM 108�s AUX-IN jack (3.5 mm ) to an AUDIO OUT or headphone jack on an external equipment (such as CD player, or VCR).
AUX-IN

6 7

OPE

N / CLO S

E

1 2

STANDBY-ON

SOURCE

BAND

PROG/CLOCK

-

VOLUME

+

TUNING

Tuning to radio stations 1 2 3
Select TUNER source. � is displayed.
TUNER

Setting the clock 1 2 3 4 5
In Standby mode, press PROG/CLOCK button. � The clock digits for the hours flash. Press ¡1 / 2� to set the hours. Press PROG/CLOCK again. � The clock digits for the minutes flash. Press ¡1 / 2� to set the minutes. Press PROG/CLOCK to confirm the time. Note: � If the clock has not been set, -- --:-- -- will be displayed.

Press BAND (TUNER on the remote control) once or more to select your waveband. Turn TUNING 0 to tune to a station. � Display shows: the frequency of the tuned station.

� In standby or during playback, press TIMER once. � Display shows if activated, and disappears if deactivated.

Activating and deactivating SLEEP
The sleep timer enables the system to switch off by itself after a set period of time. The clock time needs to be set first before the sleep timer can be used. � Press SLEEP on the remote control repeatly to select desired time before system shuts off. � Display shows SLEEP and
SLEEP TIMER

Maintenance
Cleaning the Cabinet � Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives. Cleaning Discs � When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. � Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records. Cleaning the disc lens � After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner.

Setting the timer
� The system can be used as an alarm clock. CD or TUNER can be set to switch on at a preset time. The clock time needs to be set first before the timer can be used. � If no button is pressed within 90 seconds during timer setup, the system will exit timer setting mode automatically.

series of time options for selection: , , ,,

,

...

� To deactivate, press SLEEP on the remote control once or more until � � is shown, or press STANDBY ON y on the system or remote control.

1 2 3
9

In any mode, press TIMER on the remote control for more than 2 seconds. Press ¡1 / 2� (or CD / TUNER on the remote control) to select sound source. Press TIMER to confirm your desired source. � The clock digits for the hours flash. 10