|
|
|
Kto jest w sklepie?
Sklep przegląda 5867 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
MC-V5037-01
3.5.
3.5.1.
Power Cord Replacement
Removal
and in place, stop, remove the cover and make sure that no wires are being pinched. DO NOT USE A POWER SCREWDRIVER TO SECURE THE COVER. NOTE: For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage.
1. Remove the dust cover and switch cover to expose the electrical connections of the power cord, ON/OFF switch, and wire cord.
3.6.
3.6.1.
On / Off Switch
Removal
1. Remove the dust cover and switch cover to expose the electrical connections of the power cord, ON/OFF switch, and wire cord. 2. Remove the ON/OFF switch by depressing the switch retaining tabs while pushing up out of the dust compartment at the same time.
3.6.2.
2. Remove the two (2) cord stopper screws (for power cord replacement), the wire connectors, and wire tie, if present.
Installation
1. Insert the new ON/OFF switch with the numbers 1,2,3, facing toward you, into the dust compartment until secured by the retaining tabs. Use a wire tie with the part number listed in the Parts List (Body) and place it in the location shown in the illustration taking care not to overtighten it. Tuck the wire connectors back into the dust compartment as shown in the close-up. 2. Ensure that the Insulator Packing is installed correctly. 3. Replace the switch cover, the two (2) switch cover screws, and the dust cover. Care should be taken not to pinch wires and make sure that the switch cover goes on easily and stays flat. If there is resistance to the switch cover lying flat and in place, stop, remove the cover and make sure that no wires are being pinched. DO NOT USE A POWER SCREWDRIVER TO SECURE THE COVER.
3.7.
3.7.1.
3. Pull the power cord out of the dust compartment for power cord replacement.
Motor Protector Replacement
Removal
1. Remove the dust cover and dust bag. 2. Remove the motor protector by pushing in, one at a time, on the tabs that secure it to the dust compartment. Push the motor protector out the back of the dust compartment. 3. Once the motor protector has been removed it can be disassemble using a pair of needle nose pliers at an angle and in a position where one side of the pliers is against the locking tab, exert enough pressure on the tab to release it, NOTE: There are two locking tabs present, but only one needs to be released. For reassembly look at the exploded view in the Parts List (Body)..
3.5.2.
Installation
1. Insert the new power cord into the dust compartment as far as necessary in order to place a new cord stopper in proper location on power cord. The proper location is approximately one and one eighth inches/thirty millimeters (1 1/8�/30 mm) of new power cord outer jacket extending past the cord stopper. Attach wires with wire connectors according to the wiring diagram in the front of this manual. ONLY USE A NEW CORD STOPPER, DO NOT REUSE A CORD STOPPER. 2. Ensure that the Insulator Packing is installed correctly. 3. Replace the switch cover, the two (2) switch cover screws, and the dust cover. Care should be taken not to pinch wires and make sure that the switch cover goes on easily and stays flat. If there is resistance to the switch cover lying flat 11
|
|
|
> |
|
