|
|
|
Kto jest w sklepie?
Sklep przegląda 5426 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
MD-MT170E
Error Messages
ERROR MESSAGES BATT EMPTY BLANK MD
q q
MEANING The battery has run down. Nothing is recorded.
ERROR MESSAGES Can'tSTAMP
q
MEANING Stamp function does not work.
(Check the number of tracks.) Can'tWRITE DEFECT!
q q
(Replace the disc with a recorded disc.) Can't COPY
q
You tried to record from a copy prohibited MiniDisc.
Cannot save the TOC information correctly to a MiniDisc. The disc is scratched.
(Record using the analogue cable.)
q
You tried to record signals other than music (such as data). A track cannot be edited. DISC FULL Er-MD (**)
(If the recorded sound is not right, retry recording or replace the disc with a recordable one.)
q q
Can't EDIT
q
The disc is out of recording space. The microprocessor has reported a system fault and the unit is out of order.
(Change the stop position of the track and then edit it.) Can't PLAY Can't READ (*)
q q
You tried to play back a track that cannot be played with this equipment. The disc data cannot be read because the disc is damaged. HOLD LOCKED
(To have it repaired, go to the distributor where you purchased the unit.)
q q
The unit is in the hold mode. You removed a MiniDisc whilst recording or editing.
(Reload the Minidisc or replace it with another one.) Can't REC
q
Recording cannot be performed correctly due to vibration or shock. NO DISC
(Turn off the power before removing the MiniDisc.)
q
A disc has not been loaded.
Number or symbol appears in (*) position.
ERROR MESSAGES NO SIGNAL
q q
MEANING Poor connection of the digital cable. No output signal comes out from the connected unit to playback.
ERROR MESSAGES TEMP OVER
q
MEANING The temperature is too high.
(Turn off the power, and wait for a while.) TOC FORM (**)
q
(Use the AC power for the connected unit.)
q
There is an error in the recording signal.
The input signal has improper sampling frequency. You tried to record on a playback-only disc. The write protection tab of a MiniDisc is set to the protected position. You tried to record on a playback-only disc. Since a track number is currently being located or updated, the unit cannot accept your command.
(Erase all of the tracks, and then record again.) TOC FULL
q
PLAY MD PROTECTED
q q
There is no space left for recording character information (track names, disc names, etc.). The track has been protected from being erased.
Tr. Protect
q
q
(Edit the track with the device on which it was recorded.) ? DISC
q
SORRY
q
A disc which contains data other than music was played.
(Wait for a while and try the operation again.)
(A disc which contains nonmusic data cannot be played.)
q
There is an error in the signal recorded on the disc.
Number or symbol appears in (*) position.
�6�
|
|
|
> |
|
