|
|
|
Kto jest w sklepie?
Sklep przegląda 5827 gości i
3 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
4-5. Temperature Compensation Offset Adjustment
Save the temperature data at that time in the non-volatile memory as 25 �C reference data. Note : 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 �C to 28 �C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature. Adjusting Method : 1. Rotate the AMS knob and display �TEMP ADJUST�. 2. Press the ENTER/YES button and select the �TEMP ADJUST� mode. 3. �TEMP = � and the current temperature data will be displayed. 4. To save the data, press the ENTER/YES button. When not saving the data, press the EDIT/NO button. 5. When the ENTER/YES button is pressed, �TEMP = SAVE� will be displayed for some time, followed by �TEMP ADJUST�. When the EDIT/NO button is pressed, �TEMP ADJUST� will be displayed. Specifications : The �TEMP = � should be within �E0 - EF�, �F0 - FF�, �00 - 0F�, �10 - 1F� and �20 - 2F�.
4-6. Laser Power Adjustment
Connection :
Laser power meter
Optical pick-up objective lens
Digital voltmeter
BD board TP (I + 5V) TP (IOP)
Adjusting Method : 1. Set the laser power meter on the objective lens of the optical pickup. (When it cannot be set properly, press the 0 button or ) button and move the optical pickup.) Connect the digital volt meter to TP (IOP) and TP (I+5V). 2. Rotate the AMS knob and display �LDPWRADJUST�. (Laser power : For adjustment) 3. Press the ENTER/YES button twice and display �LD $ 4B = 3.5 mW�. 4. Adjust RV102 of the BD board so that the reading of the laser power meter becomes 3.4 +0.1 mW. �0 5. Press the ENTER/YES button and display �LD $ 96 = 7.0 mW�. (Laser power:MO reading) 6. Check that the laser power meter and digital voltmeter readings satisfy the specified value. Specification :
Laser power meter reading : 7.0 ± 0.3 mW Digital voltmeter reading : Optical pickup displayed value ± 10%
(Optical pickup label)
KMS
210A 27X40 B0825
lop = 82.5 mA in this case lop (mA) = Digital voltmeter reading (mV)/ 1 (�)
7. Press the ENTER/YES button and display �LD $ 0F = 0.7 mW�. (Laser power: MO reading) 8. Check that the laser power meter at this time satisfies the specified value. Specification :
Laser power meter reading : 0.70 ± 0.1 mW
9. Press the EDIT/NO button and display �LDPWR ADJUST�, and stop laser emission. (The EDIT/NO button is effective at all times to stop the laser emission.)
� 40 �
n
|
|
|
> |
|
