|
|
|
Kto jest w sklepie?
Sklep przegląda 5295 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SECTION 3 ADJUSTMENTS
PRECAUTION 1. The adjustments are performed in the sequence that they are described. 2. The required test tapes are: TY-7111 (8-909-812-00) ................................. Level TY-7252 (8-909-822-00) ................................. Tracking TY-7551 (8-909-814-00) ................................. Function TY-30B (8-892-358-00) ................................... Blank The required torque meter is: TW-7131 (8-909-708-71) ................................ FWD 3. Switch and Control Settings REMOTE switch : OFF REC MODE switch : 48k (STANDARD) REC LEVEL control : Minimum PHONE LEVEL control : Minimum 4. Preparation of End Sensor Cassette (1) Push the slider locks of a cassette tape and slide the slider in the direction of the arrow.
hub hole slider lock slider
7 Cassette holder assy 3 Cassette 4 Push down the holder spring in the direction 2 BVTP 3 � 6
6. When adjusting tape pass and each guide, as shown below, it is a good practice to remove the holder assy and use the DAT cassette holder (J-8000-002-A). This facilitates adjustment work. � When removing and installing the holder assy, turn the pulley counterclockwise and set loading OUT condition for easy removal and installation. � When adjusting, turn the pulley clockwise and turn on the CASSETTE TABLE IN switch (S2) to set loading IN condition. Then, set the test tape.
8. After adjustment is completed, perform the following checks to verify the tape speed. (1) Check that with the REC MODE switch set to STANDARD 48k, tape is normally recorded and played back. (�1) (2) Check that with the REC MODE switch set to LONG, tape is normally recorded and played back. (�0.5) (3) Check that in performing the CUE (� + )) or REVIEW (� + 0) operation, �kyur kyur� sound is heard. (�3, �8) Adjustment Location: mechanism deck block
(4) Check that after performing the FF ()) or REW (0) operation, the time display is appropriate. (�16) (5) Check that the AMS (+, =) operation is normal.
1 BVTT 3 � 8 5 Nylon washer 6 Step screw
T1 guide
S1 guide
T2 guide
hub hole slider lock
7. Test Mode � To enter the test mode, short between TP (MAIN-TEST) and the GND on the DIGITAL board, then turn on the power. The meter scale within the fluorescent indicator tube (FL701) will flash. Press the OPEN/CLOSE 6 key and set the test tape. (The specified tape should be used for each adjustment.) Test Mode (Short between TP (MAIN-TEST) and GND) 1 Have �DPG� display lit in the fluorescent indicator tube. (Press the AMS + key.) � S2, T2 and F Guide Adjustments � End Sensor Adjustment � Tape Pass Fine Adjustment (�1.5FWD mode) � DPG Adjustment 2 Have �TR� display lit in the fluorescent indicator tube. (Press the � key.) � FWD Torque Adjustment � FWD Back Tension (Torque measurement mode) Adjustment � To release the test mode, remove the short between TP (MAINTEST) and GND. After necessary adjustment is completed, be sure to release the test mode.
S2 guide
F guide
(2) Open the cassette lid and cut tape.
cassette lid cut tape slider tape
(3) Turn the hubs to take-up tape (for both T and S sides). The end sensor cassette tape for end sensor adjustment is now prepared. 5. Take care never to turn RV1 and RV2 within the RF AMP board of the cassette compartment section.
� 19 �
� 20 �
|
|
|
> |
|
