|
|
|
Kto jest w sklepie?
Sklep przegląda 5965 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
 ;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
;
Instrukcja Serwisowa jest kompletna i czytelna. Dziękuję!
;
Wszystko OK!
Dokumentacja jest czytelna.
Dziękuję.
;
Bardzo dobra jakość skanu, przystępna cena. Instrukcja serwisowa okazała się przydatna przy "reanimowaniu" dwudziestoparoletniego decka, który teraz pięknie gra :)
1
2
3
4
A
8. ETC.
1 1 5 10 15 20 25 30 32
P AN E L
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
7 Key operation
<DOWN> <UP> <SEL> <SET> : Shifting to MASK SETUP (+) : Shifting to PANEL REVISE (+) : MASK ON/OFF : Shifting to the next nested layer
5
10
B
15 16
E TC .
(+)
1 1
5
10
15
20
25
30
32
7 Key operation
<DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment value <LEFT> : Subtracting by one from the adjustment value <SET> : Determining the setting value and shifting to the upper layer <SEL> : MASK ON/OFF
P AN E L E TC .
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
5
C
10
15 16
B AC K U P
E E P R OM
<=>
: NO
OPRT
D
<Lower-layer items of ETC.> No. Items Adjustment/Setting Value Remarks
"ERR" is indicated when no data are in the backup EEPROM. To activate the option to select TRANSFER, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
1
BACKUP DATA <=>
<=>NO OPRT<=>TRANSFER<=>
2
E
DIGITAL EEPROM <=> <=>NO OPRT<=>REPAIR/DELETE<=>
"DELETE" is indicated when the main unit has been already adjusted. To activate the option to select REPAIR/DELETE, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
3 4 5 6 7
PD INFO. <=> SD INFO. <=> HR-MTR INFO. <=> PM/B1-B5 <=> P-COUNT INFO. <=>
<=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> To activate the option to select CLEAR, repeatedly press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
F
� "NO OPRT" is selected when this submode is entered (to avoid accidental misoperation). � When each item is set, the process starts then the unit shifts to the upper layer. (When NO OPRT is determined, the unit will shift to the upper layer without doing anything.) � When data are set to be backed up, if the digital EEPROM has not been adjusted, do the operation of LED pattern No. 7.
72
1 2
PDP-436PE
3 4
|
|
|
> |
|
