jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
Tekstowy podgląd strony 6 (kliknij aby zobaczyć)
Using the Glasstron (continued)
2
If the screens are aligned, press the START/BATT CHECK button.
Left screen Right screen
3 4
Start playback on the video equipment connected to the Glasstron. Adjust the volume by turning the VOL control.
When you set the AVLS ON/OFF switch to ON, you cannot turn up the volume beyond the defined limit (see page 24).
Correct The combined picture you see with both eyes
You may see a horizontal line on the left screen rather than the right screen and vertical lines on the right screen rather than the left screen. This is not a malfunction.
If the image you see matches one of the pictures below, you have correct screen alignment. Correct Correct Correct Correct lower
VOL
louder
Operations Operations
5
START/BATT CHECK
Check that the four corners of the screen are clear.
If the four corners of the screen are not clear, do the step 2 (page 22) to check the screen position alignment again.
6
If the image you see matches one of the pictures below, stop using the Glasstron immediately. Use of the Glasstron under such conditions may cause eye fatigue or eye damage.
Incorrect Incorrect Incorrect
Adjust the brightness by turning the BRIGHT control.
BRIGHT
�| �{
less bright
brighter
When no vertical lines cross the horizontal line.
When the horizontal line appears as a diagonal line.
When the center vertical line does not cross the horizontal line.
If you cannot see a proper arrangement of these lines even after resting your eyes for a few hours, the Glasstron may not be operating correctly. Contact your Sony dealer or local authorized Sony service facility.
continued
22-US
23-US
Using the Glasstron (continued)
Setting the user lock
Screen warnings against overuse of the Glasstron
To prevent eye fatigue or eye damage, after you use the Glasstron for three hours the following caution appears on the screen and the power turns off automatically.
After you finish using the Glasstron
Take off the Glasstron, and turn off the power. Note on the LCDs
The LCD screen is made with highprecision technology. However, black points or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is not malfunction. (Effective dots: more than 99.99%)
WARNING
This product should not be used by children age 15 or younger. The eyes of children are still developing and may be adversely affected by use of this product. To prevent such use, this product is equipped with the user lock system. When the user lock is on, audio and video signals are not input and all operations except power on/off are disabled. To use the Glasstron, unlock the user lock.
TIME OUT
Set the user lock switch as shown in the illustration.
1
TEMPS DEPASS USER LOCK
Preventing sound from escaping through the stereo headphones �� AVLS(Auto Volume Limiter System):
Keeps down the maximum volume to protect your ear. You cannot turn up the volume beyond the defined limit even if you try to turn it up.
Caution: Motion sickness from viewing programs.
VERR. UTILIS
Set the AVLS ON/OFF switch to ON.
Some viewers may experience motion sickness, headache or nausea from viewing movies or video programs, especially those with intense action and movement. If you feel any of these symptoms, stop using the product immediately. To avoid personal injury or injury to others, do not drive a car or motorcycle, nor do anything that requires concentration until the symptoms disappear.
Bottom of the Power supply box
Lock
Unlock
To unlock the user lock
Set the user lock switch to the opposite position.
Caution: Motion sickness from external motion.
Do not use the product while subject to external motion �� for example, as a passenger in a car. Use of this product under these conditions may cause motion sickness.
A VLS OFF ON
To turn the AVLS off
Set the AVLS ON/OFF switch to OFF.
