4 Adjust the surround speaker output levels
(from �10 dB to +10 dB).
� Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers. To adjust the left surround speaker level, press SURR L +/�. To adjust the right surround speaker level, press SURR R +/�.
L SUBWFR R DSP VOL
5 Turn MULTI JOG until the setting item you want
to set appears on the display, then press SET.
� As you turn MULTI JOG, the indication changes as follow:
L LPCM SUBWFR R DSP VOL
LPCM
BASS CENTER EFFECT* B.BOOST
TREBLE SUBWFR SURR L SURR R PANORAMA BAL ATT (Back to the beginning)
Ex.: When selecting ��8 (dB)� for �SURR R.�
* Available only for DAP modes. SURR L*1: To adjust the left surround speaker output level (from �10 dB to +10 dB).
5 Press TEST again to stop the test tone. 6 Only for DAP modes:
Press EFFECT to select the DAP effect level (1 to 5) you want.
� As the number increases, the DAP effect becomes stronger (normally set it to �EFFECT 3�).
LPCM L SUBWFR R DSP VOL
SURR R*1:
To adjust the right surround speaker output level (from �10 dB to +10 dB).
EFFECT (available only for DAP modes) *2: To adjust the DAP effect level. As the number increases, the effect becomes stronger (normally set it to �EFFECT 3�). *1 �0 (dB)� is the initial setting for each speaker setting. *2 �3� is the initial setting.
EFFECT 3
EFFECT 4
EFFECT 5
6 Turn MULTI JOG to adjust the item selected in
step 5, then press SET.
Your setting is stored. � When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.
L SUBWFR R DSP VOL
EFFECT 2
EFFECT 1
On the front panel:
� No test tone is available when using the buttons on the front panel.
SOURCE SELECTOR / MULTI JOG MASTER VOLUME PHONES
LPCM
DIMMER SETTING ADJUST SURROUND SET / TUNER PRESET
STANDBY / ON
STANDBY
DVD MULTI
DVD
DBS
VCR
TV
FM / AM
Ex.: When selecting ��8 (dB)� for �SURR R.�
Before you start, remember... There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
7 Repeat steps 5 and 6 to adjust the other
settings.
1 Start playing 2 channel software�either Linear
PCM or analog signal�and select the source.
2 Press SURROUND.
MULTI JOG now works for the Surround/DSP mode selection.
To cancel DSP Modes Press SURROUND repeatedly on the remote control or press SURROUND then turn MULTI JOG on the front panel so that �STEREO� appears on the display. The DSP indicator goes off from the display.
3 Turn MULTI JOG until one of the DSP modes you
want to apply appears on the display.
The DSP indicator lights up on the display. � As you turn MULTI JOG, the indication changes as follow:
LPCM L SUBWFR R DSP VOL
NOTES � You can adjust the speaker output levels using the remote control without outputting the test tone. � You cannot adjust the center speaker output level and no test tone comes out of the center speaker when �CNTR SP� is set to �NO.� � You cannot adjust the surround speaker output levels and no test tone comes out of the surround speakers when �SURR SP� is set to �NO.�
PLII MOVIE LIVE CLUB
HALL ALL CH ST.
(Back to the beginning)
PLII MUSIC DANCE CLUB
PAVILION STEREO (Surround/DSP off)
4 Press ADJUST.
MULTI JOG now works for the sound adjustment.
