Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5615 gości 
Kategorie
Informacje
Polecamy
Strona główna >> SAMSON >> S2000 Instrukcja Obsługi
 
 0 szt. w koszyku 

SAMSON S2000
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis SAMSON S2000 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 8 (kliknij aby zobaczyć)
The S1500 / S2000 Protection Circuitry
As noted in the �Guided Tour� section of this manual, the S1500 / S2000 frontpanel Protection LED indicates the activity of the relay speaker connection circuitry. When the Protection LED is lit, this circuitry is active, and all connected speakers are muted (provided with 0 volts DC), thus protecting them and preventing any audible �thump� from occurring. The following conditions will cause the Protection LED to go on: � Initial power-up: For approximately five seconds after initial power-up, the protection circuitry is activated and the speaker output is muted. If everything is operating normally, you will hear an audible click at the conclusion of this brief period, as the protection circuitry is deactivated and the S1500 / S2000 begins delivering signal to connected speakers (at which point you�ll hear a click). It is normal for the Protection LED to fade gradually after the amplifier is powered off. WARNING: If the Protection LED fails to go out (and you fail to hear the accompanying audible click) approximately five seconds after power-up, turn the S1500 / S2000 off immediately and check all external devices and wiring for possible shorts or other defects. � Overheating: A temperature sensing device in the S1500 / S2000 will cause the protection circuitry to be activated (and the Protection LED to go on) whenever the operating temperature of the unit rises above a safe level. To guard against this problem, make sure the S1500 / S2000 receives adequate ventilation on all sides and that both the front and rear panels are unobstructed. � Severe overcurrent conditions: This occurs whenever the signal being input to the S1500 / S2000 rises to a level above 20% THD (Total Harmonic Distortion). � Shorted speaker cables: This will occur if, due to faulty wiring, the hot and ground signals being output by the S1500 / S2000 short one another. � Output impedance drops below 2 ohms: This can occur if the S1500 / S2000 is connected to inappropriate speaker systems (see the �Setting Up and Using Your S1500 / S2000� section on page 5 in this manual for more information). � DC voltage detected at speaker output: The most likely cause of this is an internal failure.

PROTECTION

In general, any time the Protection LED lights up (other than during the approximately five seconds following initial power-up), there is reason to be concerned. If this occurs, turn the S1500 / S2000 off immediately and carefully check all wiring and external devices in order to locate and correct the condition that caused the LED to light up in the first place. For further assistance, contact your local Samson dealer. If purchased in the United States, you can call Samson Technical Support (1-800-372-6766) between 9 AM and 5 PM EST.

6

Klienci kupując ten produkt kupili także
>
Parse Time: 0.181 - Number of Queries: 107 - Query Time: 0.048