|
|
|
Kto jest w sklepie?
Sklep przegląda 5533 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
�
If the mode is to be set in combination with other options, use the table shown below to add up the total of the setting values for all the peripheral devices to be set, and set that total value. For example, if the SF-A56 and sorter are to be set, the total setting value is 1 + 10 = 11. Operate the keys as follows:
The leading edge position can be adjusted within a range of 8 mm (8 steps) on the stopper side and 7 mm (7 steps) on the glass side in 1 mm increments. Adjustment can be done separately for the one-sided, two-sided, and thin paper modes.
8
/
0 0
0
1
2
3
8 mm
4
5
6
9
0/ 00 01 02 03 04
6 mm
SF-A17 SF-A56
1 1
Stand/paper drawer
4
Sorter Staple sorter
10 10
Stopper
Glass
8. Adjust the center of the copy.
Set an original in the ADF tray and make a copy. When the copy is off center as shown in Fig. 1 or Fig. 2, loosen the two tray securing screws and adjust the tray by moving it in direction A orB as shown in the figure.
V iew from the operator side
Setup example
(1) If the leading edge of the original was not fed all the way to the stopper, enter value which will move the original toward the stopper side. 7, 6, 5, 4...
Original
Mark
Tray securing screw
B
A
Stopper
Glass
(2)
If the copy image at the leading edge was distorted, enter value which will move the original toward the glass side. 9, 10, 11...
Original Stopper
Glass
5 When off center as shown in fig. 1 Move the tray in direction A and secure it with the two mounting screws. Make a copy to check whether it is centered properly.
Fig. 1 Center of copy paper
Stopper
(3)
If the original overrode the stopper, enter value which will move the original toward the glass side. 9, 10, 11, 12 ...
Original
Glass
�
Center of original image (first copy)
After selecting test command 53 , enter a selected set value between 0 and 15 using the copier keys.
C
5 When off center as shown in fig. 2 Move the tray in direction B and secure it with the two mounting screws. Make a copy to check whether it is centered properly.
Fig. 2 Center of copy paper
0/
4
2
(a)
0/
0
(b)
1
(a) One-sided mode (b) Two-sided mode (c) One-sided thin paper mode *For SF-A17, only (a) and (c) are possible.
(c)
2
Center of original image (first copy)
9. Adjust the position of the leading edge of originals
� �
The position of the leading edge of originals fed from the ADF can be determined using test command 53 . Although the leading edge has been factory set to stop at location (8), it may need to be adjusted depending on the type of originals. �4�
Set to between 0 and 15 as dictated by the copier's performance. The factory setting is "8".
|
|
|
> |
|
