|
|
|
Kto jest w sklepie?
Sklep przegląda 5786 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SM-SX1H
TROUBLESHOOTING
� Power is not supplied. Does AC100V stand between Pins 1 and 2 of the power filter PWB connector CNP502? Yes Is any normal voltage is output from the power PWB B1503/CNS503? Yes No � Check the output voltage (OYT terminal) of UNT501 and UNT502. � Check the parts (L504 to L511, F502, FS503 and R503 to R506) on the power PWB. � Check the 1-bit amplification unit. (Try to disconnect CNWAM4 and CNWAM3.) (LED does not come on and it does not sound.) � Check the fuse F501. � Check the parts on the power filter PWB. � Check the wiring of the inlets SOC501 and CNS501.
No
Is 5V supplied to Pin 13 of the microcomputer IC907? Yes Is any oscillating waveform found at Pins 14 (OSC2) and 15 (OSC1)? No
� Check IC306 output. � Check R391.
No
� Check X900. � Check IC907.
� It neither sound at the analog nor digital input. Are the speaker relays RLY201 and RLY202 switched? Yes Are they properly wired to the 1-bit amplifying unit? (CNWAM1, CNWAM2, CNWAM3, CNWAM4)
(when power is supplied and LED is lit.) � Check whether 12V is supplied to RLY201 and RLY202 or not. (Check the surroundings of Q201, Q202, R201 to R202.) � Check whether Q203 and Q204 are on or not. � Check the line Q203 and Q204 from Pin 41 of the microcomputer IC907.
No
Is voltage properly supplied to 1-bit amplifier? (CNP306)
No
� Check whether the proper voltage is output from the AC input filter CNP502 or not. � Check whether RLY303 is activated or not. � Check whether Q303 is on or not. � Check the line Q303 from Pin 42 of the microcomputer IC907. � Check -22V (around Q115 and Q114). � Check 5V (around Q105 and Q106). � Check reset 5V. (Connection from Pin 21 of the microcomputer IC904.) � Check CNS601A/B and main volume, VOL601. � Check the IC107 output voltage which is supplied to drive the relay. � Check the relays RLY601 and RLY602 and drive circuit.
Yes
Is voltage properly supplied to 1-bit amplifier? (CNP305) No Yes
Is any signal output from the connectors CNP303 and CNP304 for 1-bit amplifier? Yes
No
Check the inside of the 1-bit amplifying unit.
� 34 �
|
|
|
> |
|
