Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5487 gości i 
2 zarejestrowanych klientów 
Kategorie
Informacje
Polecamy
Strona główna >> OTHERS >> SON OF BERTHA Instrukcja Obsługi
 
 0 szt. w koszyku 

SWR SON OF BERTHA
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis SWR SON OF BERTHA Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 21 (kliknij aby zobaczyć)
IMPEDANCE (continued)
one 8 ohm enclosure, you know you can add one more 8 ohm speaker safely (8 divided by 2 = 4). Although much less common, you could also add one, or even two, 16 ohm cabinets: two 16 ohm cabinets in parallel have the same total impedance as one 8 ohm speaker. To get the most efficiency out of your system with the fewest cabinets, your best choice would be to connect two 8 ohm enclosures. Since you would be driving two cabinets of equal impedance, each will receive half the power your amp can deliver. If your amplifier delivers 200 watts RMS at 4 ohms, then each cabinet will receive 100 watts RMS maximum under clipping. (Clipping is the point where the power amplifier runs out of headroom and begins to distort.) If you had four 16 ohm enclosures, each one would receive a maximum of 50 watts RMS under clipping. Continuous clipping is very harmful to speakers, especially in a bass system: the lower the note, the longer the duration of DC content in the clipped signal. To understand what happens under this condition, remember the example of what speakers do when a 9 volt battery is applied to them. Now imagine what 20 or even 50 volts would do at the rate of 40 times per second! The results can be overheating, disfiguring of the voice coil, overall fatigue, and�eventually�complete failure.

TROUBLESHOOTING GUIDE
�I�m hearing unwanted distortion through my cabinet.� This could be for a variety of reasons, but is probably being caused by one of the following three sources: 1) the amplifier, 2) the cabinet�s woofer(s), and 3) the cabinet�s tweeter. The best way to figure it out is to try and isolate �the big three.� If you have access to another (working) bass cabinet, hook your amp up to it. If things are still distorting, it�s probably your amp. Consult your amplifier owner�s manual for troubleshooting that piece of gear. To determine whether the distortion�s coming from the tweeter or the woofers, first put your ear up to the cabinet, play some notes, and see if you can hear where it�s emanating from. If you can�t quite narrow it down, try turning the Tweeter Attenuator control all the way down (counter-clockwise). When this control is all the way down, the tweeter is effectively �off.� Play some notes�if you hear distortion, you know it�s not the tweeter (see next paragraph�). If you don�t hear any distortion with the tweeter off, try turning up the Tweeter Attenuator. It may be that you just need to find the optimum tweeter level for your bass, amp, or style of playing. If the tweeter distorts no matter what level the Tweeter Attenuator control is set to, it�s probably best to call SWR�s Service Department. The number�s (818) 253-4797. If the tweeter�s off AND the amp�s okay, and you�re still hearing distortion, there may be a problem with your woofer(s) and/or the cabinet�s internal workings. Inspect your woofers� cones for folded edges. There�s a very slight chance you have a defective woofer. Or, you may have blown one or all of them by driving them too hard. Speakers that have been overdriven are easy to detect, and generally do not fall under a manufacturer�s warranty. You should call SWR�s Service Department to determine your next move. The number�s (818) 253-4797. �I hear intermittent distortion and/or crackling coming from the cabinet.� This could be due to a bad speaker cable, or a bad speaker cable connection. First, make sure the cable is securely connected to both the cabinet and the amp (or other cabinet). If you�re using more
BASS SPEAKER ENCLOSURES OWNER�S MANUAL � 19

Klienci kupując ten produkt kupili także

$4.99

SX-K700 TECHNICS
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

CJ-V51 PIONEER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

SX-PR602 TECHNICS
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EV-S1000E SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

AG7330 PANASONIC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EVO-9850 VOLUME 1 SONY
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.208 - Number of Queries: 125 - Query Time: 0.054