|
|
|
Kto jest w sklepie?
Sklep przegląda 6020 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
[Aging Mode] � Execute only if connected to the HTC-NX1. This mode can be used for operation check of CD section and tape deck section. CD section and tape deck section work in parallel. � If an error occurred: The aging operation stops only an error occurred sections and display then status. � If no error occurs: The aging operation continues repeatedly. Procedure: 1. Set disc in DISC5 tray. 2. Load the tapes into the decks A and B respectively. 3. Press the [PLAY MODE] button to set the �ALL DISCS� mode, and press the [REPEAT] button to �REPEAT� off. 4. Press the [CD] button to select the function �CD�. 5. Press three buttons of [ENTER] , [POWER SAVE/DEMO] , and [TUNER BAND] simultaneously. 6. The aging mode is activated, if the indicator of disc tray number on the liquid crystal display is blinking. 7. To release from the aging mode, press the ?/1 button to turn the power OFF and operate the cold reset. (Refer to the �MC Cold Reset�) 1. Display at the Aging Mode � Display operating state of CD section and tape deck section alternately. � If an error occurred, stop display which that section. 2. CD Section � Display at the aging mode is the same as the normal operation. � The sequence during the aging mode is following as below. Aging mode sequence (CD section) :
� Display at an error occurred 1) Display of the error count (1) Press three buttons of [ENTER] , [POWER SAVE/DEMO] , and [GROOVE] simultaneously. (2) Display of the error count following as below. Display
EMC**EDC**
Notes: EMC**: The number of mechanical error. EDC** : The number of no disc error after chucking the disc.
2) Display of mechanical error Display
E**M##$$&&
Notes: ** : The number of mechanicalbutton to changes next error display) error.(�00� is latest one) (Press the [PLAY MODE] ## : Not used. $$ : Loading error. (Second figure is not used) D : The error in the midst of close at the except mechanical trouble. E : The error in the midst of open at the except mechanical trouble. C : The error in the midst of chuck up at the except mechanical trouble. F : The error in the midst of EX-open at the except mechanical trouble. &&: Loading error. (Second figure in not used) 1:The error in the midst of chuck up. 2:The error in the midst of chuck down. 3:Time up of EX-open 4:Time up of EX-close.
Open the disc1 tray
3) Display of no disc error Display
Disc5 chucking
E**D##$$&&
Disc5 TOC read
Notes: ** : The number of mechanical error.(�00� is latest one) (Press the [REPEAT] button to changes next error display) ##: 01: Focus error 02: GFS error 03: Set up error $$: 00: No disc error when does not chucking retry. 02: No disc error when chucking retry to completion. &&: The state when judged no disc error. (Second figure is not used) 1:Stop 2:Set up 3:TOC read 4:Access 5:Play 6:Pause 7:Manual search (Play) 8:Manual search (Pause)3. Tape Deck Section
Disc5 play track1 for 2 seconds
Disc5 play last track for 2 seconds
9
|
|
|
> |
|
