|
|
|
Kto jest w sklepie?
Sklep przegląda 5773 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
3.3.7 Removing the DVD pickup (See Figs.12 to 14) � Prior to performing the following procedures, remove the tray assemblies and DVD traverse mechanism assembly. (1) From the topside of the DVD traverse mechanism assembly, solder the short-circuit points i on the DVD pick up. (See Fig.12) Caution: Solder the short-circuit points i on the DVD pickup before disconnecting the flexible wire extending from the DVD pickup. If you do not follow this instruction, the DVD pickup may be damaged. (2) Disconnect the flexible wire from the connector on the DVD pickup. (See Fig.12) (3) Turn the screw shaft gear in the direction of the arrow 1 to move the DVD pickup in the direction of the arrow 2. (See Fig.12) Remove the screw G attaching the gear holder. (See Fig.12) Remove the screw H attaching the SS adj. spring. (See Fig.12) Move the DVD pickup in the direction of the arrow and remove the screw shaft from the section j on the screw shaft holder. (See Fig.13) Remove the section k of the DVD pickup from the guide shaft. (See Fig.13) Remove the two screws J attaching the rack arm to the DVD pickup. (See Fig.14) Pull the screw shaft from the DVD pickup in the direction of the arrow. (See Fig.14)
Short circuit points i DVD traverse mechanism assembly Connector Flexible wire
2 Screw shaft gear 1 SS adj. spring
(4) (5) (6)
G
Gear holder DVD pickup Section k
H
DVD pickup Fig.12 Guide shaft
(7) (8) (9)
3.3.8 Attaching the DVD pickup (See Figs.12 to 14) (1) Attach the screw shaft to the DVD pickup and attach the rack arm with the screws J. (See Fig.14) Reference: After attaching the screw shaft to the DVD pickup, attach the screw shaft collar to the screw shaft. (See Fig.14) Attach the section k of the DVD pickup to the guide shaft first and attach the screw shaft to the section j on the screw shaft holder. (See Fig.14) Attach the SS adj. spring and gear holder with the screws G and H. (See Fig.12) Turn the screw shaft gear to move the DVD pickup toward the left. (See Fig.12) Connect the flexible wire to the connector on the DVD pickup. (See Fig.12)
Section j
(2)
Screw shaft
(3) (4) (5)
Screw shaft holder Fig.13 DVD pickup
Caution: Unsolder the solders from the short-circuit points i after connecting the flexible wire.
Rack arm Screw shaft collar
J
Screw shaft
Fig.14
(No.MB192)1-17
 $4.99 TH-M501 JVC
Katalog Części Katalog części w formie pliku PDF. Plik zawiera wykaz części znajdujących się w urządzeniu wr…
|
|
|
> |
|
