|
|
|
Kto jest w sklepie?
Sklep przegląda 5672 gości i
11 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
TK-863G
REALIGNMENT
6-4. Function
1. If you press the [MON] switch while �PROG 576� is displayed, the checksum is displayed. If you press the [MON] switch again (while the checksum is displayed), �PROG 576� is redisplayed. 2. If you press the [A] switch while �PROG 576� is displayed, the display changes to �PROG 192� to indicate that the write speed is low speed (19200 bps). If you press the [A] switch again while �PROG 192� is displayed, the display changes to �PROG 384�, and the write speed becomes the middle speed (38400 bps). If you press the [A] switch again while �PROG 384� is displayed, the display returns to �PROG 576�. 4. Power on the slave TK-863G. 5. Connect the cloning cable (No. E30-3382-05) to the modular microphone jacks on the master and slave. 6. Press the [SCN] key on the master while the master displays �CLONE�. The data of the master is sent to the slave. While the slave is receiving the data, ��PC�� is displayed. When cloning of data is completed, the master displays �END�, and the slave automatically operates in the User mode. The slave can then be operated by the same program as the master. 7. The other slave can be continuously cloned. When the [SCN] key on the master is pressed while the master displays �END�, the master displays �CLONE�. Carry out the operation in step 4 to 6.
Note :
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one radio to another by connecting them via their modular microphone jacks. The operation is as follows (the transmit radio is the master and the receive radio is the slave). 1. Turn the master TK-863G power ON with the [ ] key held down. If the password is set to the TK-863G, the TK-863G displays �CLN LOCK�. If the password is not set, the TK-863G displays �CLONE�. 2. When �CLN LOCK� is displayed, only the [ / ] key and [SCN], and [0] to [9] keys can be accepted. When you enter the correct password, and �CLONE� is displayed, the TK-863G can be used as the cloning master. The following describes how to enter the password. 3. How to enter the password with the microphone keypad; If you press a key while �CLN LOCK� is displayed, the number that was pressed is displayed on the TK-863G. Each press of the key shifts the display in order to the left. When you enter the password and press the [SCN] key, �CLONE� is displayed if the entered password is correct. If the password is incorrect, �CLN LOCK� is redisplayed. How to enter the password with the [ / ] key; If the [ / ] key is pressed while �CLN LOCK� is displayed, numbers (0 to 9) are displayed flashing. When you press the [SCN] key, the currectly selected number is determined, and the display shifts to the left. If you press the [SCN] key after entering the password in this procedure, �CLONE� is displayed if the entered password is correct. If the password is incorrect, �CLN LOCK� is redisplayed.
Cloning cable (E30-3382-05)
Fig. 2
11
|
|
|
> |
|
