|
|
|
Kto jest w sklepie?
Sklep przegląda 5728 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
PT-11 Chassis Service Manual
SOUND IF CIRCUIT
On mono models;
The sound bandpass and trap filters have to be connected externally. The filtered intercarrier signal is fed to a limiter circuit and is demodulated by means of PLL demodulator. The PLL circuit tunes itself automatically to the incoming signal, consequently, no adjustment is required. The volume is DC controlled. The composite audio output signal has an amplitude of 700 mV RMS at a volume control setting of -6 dB. The de-emphasis capacitor has to be connected externally. The non-controlled audio signal can be obtained from pin 1 via a buffer stage. The amplitude of this signal is 350 mV RMS. The TDA8362 external audio input signal must have an amplitude of 350 mV RMS. The audio/video switch is controlled via the chrominance input pin.
On stereo models;
On stereo models, the adjustable sound output pin (pin50) is used for mono sound. An external sound IF circuit TDA3845 is used for NICAM B/G, I stereo systems. For NICAM L stereo system, TDA4470B Sound IF IC is used so that obtain AM sound and NICAM I sound carrier. On German Stereo system, TBA120U is used as FM demodulator for second sound carrier.
SYNCHRONIZATION
CIRCUIT
The sync separator is preceded by a voltage controlled amplifier which adjusts the sync pulse amplitude to a fix level. The sync pulses are then fed to the slicing stage (separator) which operates at 50 % of the amplitude. The separated sync pulses are fed to the first phase detector and to the coincidence detector. The coincidence detector is used for transmitter identification and to detect whether the line oscillator is synchronized. When the circuit is not synchronized, the voltage on the peaking control pin (pin 14) is LOW so that this condition can be detected externally The IC TDA8362 contains a start up circuit for the horizontal oscillator. When this feature is required a current of 6.5 mA has to be supplied to pin 36.
COLOR DECODING
TDA8362 contains PAL and NTSC decoder (TDA8361 contains only PAL decoder) but it can cooperate with the secam add-on secam decoder TDA8395. The communication between two IC�s is achieved via pin 32. The TDA8362 supplies the reference signal (4.43 MHz) for the calibration system of the TDA8395, identification of the color standard is via the same connection. When a SECAM signal is detected by the TDA8395 the IC will draw a current of 150 uA. When TDA8362 has not identified a color signal in this condition it will go into the SECAM mode, that means it will switch of the R-Y and B-Y outputs and increase voltage level on pin 32.
41 VERTICAL
DEFLECTION
CIRCUIT
WITH TDA3653B
The TDA3653B is vertical deflection circuit for drive of various deflection systems with currents up to 1.5 A peak to peak. Pin 5 is the output pin. the supply for the output stage is fed to pin 6 and the output stage ground is connected to pin 4. Pin 1 is the input for the driver of the output stage . The signal at pin 1 is also applied via external resistors to pin 3 which is the input of the switching circuit. When the flyback starts, this switching circuit rapidly turns off the lower output stage and so limits the turn-off dissipation. It should be noted that the lowest voltage at pin 8 is > 2.5 V, during normal operation.
17
|
|
|
> |
|
