|
|
|
Kto jest w sklepie?
Sklep przegląda 5715 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
1.8
Brief operation guide
The PIN-code system
Activate the PIN-code system
While the BeoSound 9000 is in stand-by mode you can set up the PIN-code.
Change or delete your PIN-code
While the PIN-code function is turned on you can always make changes to the PIN-code.
Using your PIN-code
When a PIN-code has been programmed, and the BeoSound 9000 has been disconnected from the mains for more than 30 minutes, you must enter the PIN-code when the BeoSound 9000 is turned back on.
p p PAUSE
NEW PIN
Press p twice followed by PAUSE to activate the PIN-code function. The display shows NEW PIN for 1.5 sec.� �then you can enter a PIN-code Press to select a digit*
p p PAUSE
PIN _ _ _ _ NEW PIN?
Press p twice followed by PAUSE to activate the PIN-code function Enter the current PINcode. The display shows NEW PIN?
PIN _ _ _ _
Enter the PIN-code Press to select a digit
m p OK
R ADIO 1
Press to accept the digit When the PIN-code has been entered the display returns to the relevant source display e.g. RADIO 1
PIN _ _ _ _
m p OK
m p
NEW PIN? PIN OFF?
Press to choose from the two options NEW PIN? or PIN OFF?
Press to accept the digit Select NEW PIN? to change your PIN-code If an incorrect PIN-code is entered the display will show ERROR and you may try again. After the �fth try, the BeoSound 9000 is turned off, and must be left in stand-by mode for 3 hours, before you can try again.
PIN _ _ _ _
The digit is replaced by a * and the next underscore blinks. Continue to enter the last three digits in the same manner. If you wish to change the entered digits� RESET Press to start entering from the beginning
Enter the new PIN-code Press to accept the new PIN-code. The display shows CONFIRM for 1.5 sec.� �then re-enter the new PIN-code
OK
CONFIRM
PIN _ _ _ _
When the PIN-code has been entered� OK Press to accept the PINcode. The display shows CONFIRM CONFIRM for 1.5 sec.�
PIN _ _ _ _
Did you forget your PIN-code?
Should you forget your PIN-code you can require a �ve-digit Master Code from your Bang & Olufsen retailer.
OK
Press to con�rm the new PIN-code The display shows that your new PIN-code is stored
�then re-enter the PINcode Press to con�rm the PINcode The display shows that your setting is stored
STORED
OK
STORED
Select PIN OFF? to delete your PIN-code When you have received a Master Code� DELETED The PIN-code function is PIN _ _ _ _ When the display is disabled and the display open for PIN-code shows DELETED for 3 sec. input� For security reasons it is only possible to change or verify the PIN-code �ve times within a period of 3 hours. If an incorrect code is entered �ve times, BeoSound 9000 is turned off, and must be left in stand-by mode for 3 hours, before you may try again. p
PIN _ _ _ _ _
If an incorrect code is entered the second time you must set up the PIN-code from the beginning.
Press the p button for more than 3 seconds to change the display to �t 5 digits
PIN _ _ _ _ _
Enter the Master Code Press to select a digit
m p OK
DELETED
Press to accept the digit The display shows that the PIN-code lock is off
*NOTE!: It is also possible to enter the digits using the number keys 0 � 9 on your Beo4 remote control.
When the Master Code is entered, the BeoSound 9000 can be used without entering the code again.
|
|
|
> |
|
