|
|
|
Kto jest w sklepie?
Sklep przegląda 5736 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
Listening to FM and AM Broadcasts
Tuning in to a Station Presetting Stations
You can preset 30 FM and 10 AM stations manually.
FM/AM
1 Press FM/AM to select either �FM�
or �AM.�
The unit automatically turns on and tunes in to
the previously received station�either FM or AM. � Each time you press the button, the band alternates between FM and AM.
MHz
In some cases, test frequencies have been already stored for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method. � There is a time limit in doing the following steps. If the setting is canceled before you finish, start again from step 2.
� If the station previously selected is stored in a preset number, the preset number will appear instead of �FM� or �AM.�
UP
On the remote control ONLY:
1 Tune in to the station you want to preset.
� See �Tuning in to a Station� on the left column.
2 Press and hold ¢ or 4 (or
UP ¢ or DOWN 4 on the unit) for more than 1 second.
PRESET GROUP
2 Press SET.
DOWN PRESET GROUP
SET
�00� starts flashing on the display.
� ¢ (UP ¢): Increases the frequencies. � 4 (DOWN 4): Decreases the frequencies. The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. � If an FM program is broadcast in stereo, the ST (stereo) indicator lights up on the display (only when the reception is good). To stop during searching, press ¢ or 4 (or UP ¢ or DOWN 4 on the unit).
When you repeatedly press ¢ or 4 (or UP ¢ or DOWN 4 on the unit) The frequency changes step by step.
MHz PRGM
3 Press PRESET GROUP
or
PRESET GROUP
UP
PRESET GROUP to select a preset number, then press SET.
The preset station is stored in memory. � Even if you do not press SET, the station will automatically be stored on the selected preset number 5 seconds later.
PRESET GROUP
DOWN
MHz PRGM
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the �MONO� appears on the display. The MONO indicator also lights up. Reception will improve.
FM MODE
You can also use the number button(s) to select a preset number. � In this case, you do not have to
1 4
2 5 8
3 6 9
OVER
To restore the stereo effect, press FM MODE again so that �STEREO� appears on the display and the MONO indicator goes off. In stereo mode, you can hear stereo sound when a stereo program is broadcast. The stereo effect also restores when: � Changing the band (FM or AM). � Changing the station frequency. � Changing the playing source. � Turning off (or on) the unit.
press SET. Ex.: To select a preset number 5, 7 press 5. To select a preset number 15, press OVER, then press 1, 5. To select a preset number 20, press OVER, then press 2, 0.
0
4 To preset more stations, repeat steps 1 to 3
above, allocating a different preset number to each station.
� Storing a new station on an already assigned number erases the previously stored one.
To reduce the beat�Beat Cut
On the remote control ONLY:
BEAT CUT
If the beats are heard, press BEAT CUT repeatedly until the beats are reduced. � Each time you press the button, the display alternates between �CUT-1� and �CUT-2.�
When you unplug the AC power cord or if a power failure occurs The preset stations will remain in the unit.
15
|
|
|
> |
|
