|
|
|
Kto jest w sklepie?
Sklep przegląda 5958 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
VRS-N8100
ACCESSORIES / CAUTIONS
Note for Servicing of the PC Control Unit (X17-1100-11)
Each unit of VRS-N8100 has its own MAC (Media Access Control) address. The MAC address is written in IC202 of the PC Control Unit. This means that replacing the PC Control Unit or IC202 results in changing the MAC address of the unit. Therefore, when the PC Control Unit or IC202 is replaced, the user should be informed of the new MAC address. Also, the new MAC address should be recorded and maintained in the servicing record together with the serial number of the unit. The MAC address can be confirmed in item �IP� setting in the Setup Menu (Network Setup).
Frequently Asked Questions (FAQ):
If you still have questions concerning the product after reading this manual, please consult the FAQ section on the KENWOOD website of your resident country (if necessary you can find a link to your local website on www.kenwood.com <http://www.kenwood.com>).
Software and Firmware update:
The latest information and procedure to update your KENWOOD PC SERVER software and VRS-N8100 Firmware can be found in the "Technical Support" / "Service" section on the website of your resident country (if necessary you can find a link to your local website on www.kenwood.com <http://www.kenwood.com>). The above-mentioned information is opened to the public.
ACCESSORIES
Remote control unit (1) For Europe RC-R0826E(A70-1651-05) For the U.S.A., Canada and Australia RC-R0826(A70-1650-05) AM loop antenna (1) (T90-0906-05) FM indoor antenna (1) For Europe and Australia For the U.S.A. and Canada (T90-0175-05) (T90-0905-05)
FM antenna adaptor (1) For Europe and Australia (T90-0827-05)
CD-ROM (PC application) (1) (W01-1835-05)
Batteries (R6/AA) (2)
Speaker cord connectors (1) (E69-0013-05)
CAUTIONS
Soft reset:
This reset procedure allows the setups made by the user to be held without being reset. (For U.S.A and Canada) Press POWER ON/STANDBY key to turn this unit OFF (STANDBY), and then press POWER ON/STANDBY key again to turn it ON. If a memory card is inserted, remove the memory card after pressing POWER ON/STANDBY key to turn this unit OFF (STANDBY). After removal, press POWER ON/STANDBY key again to turn it on. (For Europe and Australia) Press ON/STANDBY key to turn this unit OFF (STANDBY), and then press ON/STANDBY key again to turn it ON. If a memory card is inserted, remove the memory card after pressing ON/STANDBY key to turn this unit OFF (STANDBY). After removal, press ON/STANDBY key again to turn it on.
Reset to the factory default setups:
Unplug the power cord from the wall outlet, then plug it back in while holding down the POWER ON/STANDBY (For U.S.A and Canada) or ON/STANDBY key (For Europe and Australia). Please note that resetting the microcomputer will clear the contents of the memory and returns the unit to the state it was in when it left the factory.
Memory back-up function
If the power supply to the receiver is shut down for about a day or more, the following settings will be reset to the initial conditions. Please be careful. Power mode = OFF Volume level = - 66 dB Dimmer level = OFF (Brightest condition) Broadcast band = FM Frequency setting = 87.50 MHz Tuning mode = AUTO
2
|
|
|
> |
|
