6
PROBLEMS
Studio Projects electronics are extremely resistant to physical damage, but if the unit fails to work after being dropped, it should be returned in adequate packing to the supplier. A double test and inspection system means that manufacturing faults are non-existent but should any fault occur, it will be repaired (or replaced) free of charge except where the fault has been caused by physical damage. (SEE WARRANTY INFORMATION)
TROUBLESHOOTING
1) The microphone doesn't work! Have you got something plugged into the INSTRUMENT input or is the mic/line set incorrectly? (this can disable the microphone input) Is the phantom power on? (capacitor microphones). If there is indication on the VU LED, is the output volume control turned down? 2) Got signal going through but no output? Is there enough signal? Use plenty of drive. Is the output gain control turned up, and do you have a properly working monitor system? 3) I don�t get any power! Is the supplied power supply plugged in correctly? Make sure the barrel connector is pushed all the way into the socket, and be sure you have available power to the supply.
ORIGINS AND MANUFACTURE
Studio Projects Electronics are entirely designed in the USA. They are manufactured in China by 797 Audio to a specification created by Studio Projects, Torrance, California. All Studio Projects electronics are inspected and tested at the factory, then inspected and tested again at PMI Audio Groups facility prior to shipping. Studio Projects electronics meet the requirements of electronic equipment sold both in the USA, Canada, and the European Union. All Studio Projects products are CE Approved, and all power supplies are UL rated.
DECLARATION OF CONFORMITY
This analog audio processing equipment conforms to the standards and requirements of the European Economic Community. The EC Harmonized standards that have been applied are; a) Electrical equipment (safety) Regulations 1994 (S.I. 1994/3260) b) Electromagnetic Compatibility Directive (89/336/EEC) incorporating (S.I. 1992/2372)
STUDIO PROJECTS LIMITED WARRANTY
THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
PMI Audio Group warrants that all products will be free from defects in material or workmanship: A: For a period of (1) one year from the date of purchase (hereinafter the labor warranty period), PMI Audio Group will repair or replace this Product if determined to be defective. After the expiration of the labor warranty period, the Purchaser must pay labor charges. B: In addition, PMI Audio Group will supply, at no charge, replacements for defective parts for a period of (one year) from the date of purchase. During the labor warranty period, to repair the Product, Purchaser must return the defective Product, freight prepaid, or deliver it to PMI Audio Group Service Center. The product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of production. PMI Audio Group will return the repaired Product freight prepaid to the Purchaser. PMI Audio Group is not obligated to provide Purchaser with a substitute unit during the warranty period or at any time. rate. No repair or replacement by Purchaser of any Product or part thereof shall extend the warranty period as to the entire Product. The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the Product warranty, whichever is greater. 2. Exclusive Remedy: Acceptance: Purchaser�s exclusive remedy and PMI�s sole obligation is to supply (or pay for) all labor necessary to repair any product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts. If repair or replacement fails to remedy the defect, then and only in such an event, shall PMI exchange to Purchaser a new or reconditioned unit. Purchaser�s failure to make a claim as provided in paragraph 1 above or continued use of the product shall constitute an unqualified acceptance of such Product and a waiver by Purchaser of all claims thereto. 3. Exceptions to Limited warranty: PMI shall have no liability or obligation to Purchaser with respect to any Product subjected to abuse, improper use, negligence, accident, modification, failure of the end-user to follow the operating and maintenance procedures outlined in the users manual, attempted repair by non-qualified personnel, operation of the unit outside of the published environmental and electrical parameters, or if such products original identification (trademark, serial number) markings have been defaced, altered, or removed. PMI excludes from warranty coverage, Products sold AS IS and/or WITH ALL FAULTS and excludes used products which have not been sold by PMI to the Purchaser. PMI also excludes from warranty coverage consumables such as fuses and batteries, etc. 4. Proof of purchase: The dealer�s dated bill of sale must be retained as evidence or the date of purchase and to establish warranty eligibility
CONDITIONS
1. Notification of claims: Warranty Service: If Purchaser discovers that the Product has proven defective in material or workmanship, then written notice with an explanation of the claim shall be given promptly by Purchaser to PMI but all claims for warranty service must be made within the warranty period. If after investigation PMI determines that the reported problem was not covered by the warranty, Purchaser shall pay PMI for the cost of investigating the problem at its then prevailing time-and-materials
7
