CASIO WE10D-1A
Instrukcja Obsługi

USER�S GUIDE 2470
General Guide
The operational procedures for Modules 2428 and 2470 are identical. All of the illustrations in this manual show Module 2428. � Press B to change from mode to mode. Each mode is explained in detail on the following pages.
Timekeeping Mode

� After you perform an operation in any mode, pressing B returns to the Timekeeping Mode.

Alarm Mode

Stopwatch Mode

Time Setting Mode

Press

.

[Module 2470]

[Module 2428]

Timekeeping Mode
PM indicator Day of the week Day

Stopwatch Mode
� In the Timekeeping Mode, press C to switch between the 12-hour and 24-hour formats. � In the Timekeeping Mode, press A to illuminate the display for a few seconds. � Day of the week is displayed as follows. SU: Sunday MO: Monday TU: Tuesday WE: Wednesday TH: Thursday F R : Friday SA: Saturday
Mode Indicator Minutes Seconds

The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.

1/100 second

Hour

Minutes

Split time indicator

Seconds

(a) Elapsed time measurement Start Stop Re-start Stop Clear

Backlight Precautions The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. � The electro-luminescent panel that provides illumination loses power after very long use. � The illumination provided by the backlight may be hard to see when viewed under direct sunlight. � The watch may emit an audible sound whenever the display is illuminated. This is due to vibration of the EL panel used for illumination, and does not indicate malfunction. � Frequent use of the backlight shortens the battery life.

(b) Split time measurement Start Split Split release Stop Clear

(c) Split time and 1st-2nd place times Start Split
First runner finishes.

Stop
Second runner finishes. Record time of first runner.

Split release
Record time of second runner.

Clear

Alarm Mode
Mode indicator Hour Minutes

When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is switched on, the watch beeps every hour on the hour. To set the alarm time 1. Hold down A while in the Alarm Mode until the hour digits start to flash on the display. The hour digits flash because they are selected. 2. sequence. change the selection in the following Press A to � Pressing A also illuminates the display.

Time Setting Mode
PM indicator Day of the week Day

To set the time and date 1. Use B to enter the Time Setting Mode. � The second�s digits flash because they are selected. 2. Press A to change the selection in the following sequence. � Pressing A also illuminates the display.
Seconds Day of week Hour Day Minutes Month

Hourly time signal on indicator

Alarm on indicator

Hour

Minutes

Normal Alarm Mode (No digit flashes)

� Once you reach the normal Alarm Mode, you have to hold down A again until the hour digits start to flash. 3. Press C to increase the selected digits. Holding down C changes the number at high speed. � The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. � When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon (PM). 4. After you set the alarm time, press A to return to the Alarm Mode. At this time the Daily Alarm is switched on automatically. To stop the alarm Press A to stop the alarm after it starts to sound. To switch the Daily Alarm and Hourly Time Signal on and off Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence.
[Alarm on Indicator/Hourly Time Signal on Indicator]

Hour

Minutes

Seconds

3. While the second�s digits are selected (flashing), press C to reset the seconds to �00�. If you press C while the second�s count is in the range of 30 to 59, the seconds are reset to �00� and 1 is added to the minutes. If the second�s count is in the range of 00 to 29, the minute�s count is unchanged. 4. While any other digits (besides seconds) are selected (flashing), press C to increase the number. While the day of the week is selected, pressing C advances to the next day. Holding down C changes the current selection at high speed. 5. After you set the time and date, press B to return to the Timekeeping Mode. � If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically.

Both on

Both off

Daily Alarm only

Hourly Time Signal only

To test the alarm Hold down C while in the Alarm Mode to sound the alarm.

1