Notes: � The auto mode is exited automatically whenever manual PAN/TILT or ZOOM/FOCUS is performed if AUTO PAN is operating and PAN/TILT does SEQ, SORT, PATROL, or AUTO TRACK movement. Note, however, that that the contents of the setting menu do not change. To return to the auto mode, open the setup menu and then close it again. The auto mode will also activate when the self return trigger time (page 33) elapses. � During operation, the lens may enter the refresh mode. � PATROL1-4 displays only the set number of patrol routines (page 35).
4. Move the cursor to DWELL TIME, and then tilt the joystick left or right to select the start point and end point dwell time setting. Tilting the joystick cycles through the stop time display in the sequence shown below. (unit: sec)
0S � 1S � 2S � 3S � 5S � 10S � 20S � 30S
� Configuring AUTO PAN Detailed Settings
1. Perform the following steps to set the PAN start point and end point. (1) Move the cursor to POSITION, press the CAM (SET) button, and then move the cursor to START. (2) Use the joystick to move the camera to the desired PAN start point, and then press the CAM (SET) button. This defines the start point and moves the cursor to END. (3) Use the joystick to move the camera to the desired PAN end point, and then press the CAM (SET) button. This defines the start point and moves the cursor to POSITION.
**AUTO PAN** POSITION SPEED ENDLESS DWELL TIME PAN LIMIT RET TOP START END ���I���127 L H OFF 1S OFF
5. Move the cursor to PAN LIMIT, and then tilt the joystick left or right to toggle it on and off. ON : Limits manual panning to the zone between the start point and the end point. The TILT range is from horizontal to straight down. Select OFF for the ENDLESS setting (step 3) when using this setting. OFF : Allows manual panning outside the zone between the start point and the end point. PAN LIMIT PAN LIMIT allows panning in the area from the start point to the end point specified in step 1, but not in the area from the end point to the start point.
End point Camera AUTO PAN zone Start point PAN LIMIT zone
Notes: � When the panning, tilting, zooming or focusing in the SEQ, SORT or PATROL mode is controlled manually, the auto mode function should be cancelled. To activate the auto mode, select the desired auto mode again or set a time for SELF RETURN in the SET UP menu. � When 0S is selected, the camera stops without dwelling and starts. � Auto refreshing may be activated during the patrol play or the auto mode to calibrate the lens position. (6) AUTO PAN Key Setting (AUTO PAN KEY) Set the operations of the camera when AUTO PAN is executed from the system controller (page 33). 1. Move the cursor to AUTO PAN KEY, and then tilt the joystick left or right to select a camera movement mode setting. Tilting the joystick cycles through settings in the sequence shown below.
AUTO PAN � SEQ � SORT � PATROL1 � PATROL2 AUTO TRACK � PATROL4 � PATROL3
2. Move the cursor to SPEED and then tilt the joystick left or right to select a panning speed setting. Shifting the setting towards the "H" (right) side increases the speed, while shifting towards the "L" (left) side decreases it. 3. Move the cursor to ENDLESS, and then tilt the joystick left or right to turn endless panning on or off. ON : Pans from the start point to the end point, and then continues to pan in the same direction from the end point to the start point. Select OFF for the PAN LIMIT setting (step 5) when using this setting. Panning will be repeated endlessly. OFF : Pans from the start point to the end point, and then reverses direction to pan from the end point to the start point. Panning is repeated endlessly.
Notes: � Auto Mode can be started, but not stopped, with the AUTO PAN key. � PATROL1-4 displays only the set number of patrol routines (page 35). -34-
