PANASONIC WVQ117
Instrukcja Obsługi

7

Remove the two Lock Lug Fixing Screws and replace the Lock Lug with L-type. Retighten the two Lock Lug Fixing Screws (refer to the right figure).

Lock Lug Fixing Screws

13

Attach the Fall Prevention Clip (provided) to the anchor bolt. Attach the Fall Prevention (provided) to the bracket and the Fall Prevention Angle Clip.

Note: Two spacer nuts are necessary for the anchor bolt.
Lock Lug
Instructions for the Fall Prevention Clip (provided) 1. Remove the Fall Prevention Wire from the Fall Prevention Clip. 2. Insert anchor bolt from side . 3. Fold side down over side . 4. Suspend the Fall Prevention Angle Clip from the other end of the Fall Prevention Wire. above Side 1 Insert 2 Remove 3 fold down

L-type Lock Lug (provided)

Fall Prevention Wire Side
below

8

Pass the power cord and video cables of the Camera Mounting Base through the hole in this bracket, and fasten it to the bracket with the four M4-L8 Screws (provided).

Anchor Bolt

4

Anchor Bolt Fall Prevention Clip (provided)

Camera Mounting Base

Fall Prevention Wire (provided)

M4-L8 Screws (provided)

Fall Prevention Clip (provided)

Spacer nuts Existing anchor bolt

9

Fit the Slot Masking Cover (provided) over the bracket, insert the Hexagon Socket Head Screws (M3, provided) into their holes, and fasten the Ceiling Mount Ring (provided) with the two nuts (M3, provided).

Slot Masking Cover (provided) M3 Screw (provided)*2 Hexagon Socket Head Screw (M4, provided)

14

Cover the bracket with the Heat Insulator (provided).
Heat insulator (provided)

Ceiling

*1 Use two nuts. *2 Fasten finally.

Nut (M4, provided)

Heat insulator (provided)

10

Suspend the Fall Prevention Wire for the camera from the Camera Mounting Base.

* The bracket is not shown in the illustrations.

SPECIFICATIONS
Ambient Operating Temperature: Dimensions: Weight: 10�C - +50�C {14�F � 122�F} 120 (diameter) � 202 (D) mm {4-3/4� (diameter) � 7-61/64� (D) mm} 720 g {1.59 lbs}

Note: Make sure that the wire matches the Fall
Prevention Wire Fixing Angle.

Ring of the Fall Prevention Wire

Weight and dimensions indicated are approximate. Specifications are subject to change without notice.

11

Attach the camera to the Camera Mounting Base, turn the camera clockwise, and tighten the Mounting Screw (M3, provided).

Rotate 15°

STANDARD ACCESSORIES
Fall Protection Wire..........................................1 pc. Fall Prevention Clip..........................................1 pc. Ceiling Mounting Ring .....................................1 pc. L-type Base Lug ..............................................1 pc. L-type Lock Lug...............................................1 pc. Slot Masking Cover..........................................1 pc. Hexagon Socket Head Screw (M4) ...............2 pcs. Wrench for Hexagon Socket Head Screw.......1 pc. Nut (M4) .........................................................4 pcs. Screw (M3).....................................................2 pcs. Screw (M4-L8) ...............................................4 pcs. Template..........................................................1 pc. Heat Insulator ..................................................1 pc.

Mounting Screw Camera Mounting Bracket L-type Lock Lug (provided)

12

Place the Decoration Cover for the bracket on the camera. Then, pull up the Slot Masking Cover (provided).

Decoration Cover

For European and other fields: Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://www.panasonic.co.jp/global/ For U.S. , Canadian and Puerto Rican fields: Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America Security Systems www.panasonic.com/security For customer support, call 1.877.733.3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010 http://www.panasonic.ca Panasonic Sales Company Division of Panasonic Puerto Rico Inc. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809) 750-4300

Slot Masking Cover (provided)

© 2005 Matsushita Electric Industrial Co., Ltd. All rights reserved.