|
|
|
Kto jest w sklepie?
Sklep przegląda 5540 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
X92-4400-0x/4730-0x X92-4740-0x/4750-0x DISASSEMBLY AND ASSEMBLY OF MECHANISM
â� Disassembly for loading cam (30) drive arm (19), lock slider (23), and rear lock arm (24)
1) The screw (D) and the loading cam (30) are removed. Note: The screw for loading cam (D) is not reusable. Please be sure to exchange. 2) The spring (58) for trigger sliders is removed. 3) The stopper (49) is removed. 4) The spring (64) of the rear lock arm (24) is removed. 5) The screw (B) and washer (K) of the drive arm (19) are removed, and the drive arm (19) is moved back to rear side. The drive arm (19) is removed. 6) Lock arm (25 and 26), lock slider (23), rear lock arm (24) and each gear is removed.
LOADING CAM (30) 35 16 15 32 33 34 26 25 B 49 24 64 BK 19 23 65
58
D 1
â� Assembly for the loading cam (30) drive arm (19), lock slider (23), and rear lock arm (24)
1) The trigger slider (15) is fixed in the main chassis (1), and is moved back to rear side. 2) The loading slider (16) is fixed to the trigger slider (15). Note: At this time, it is cautious of the position of the hook of the loading slider (16). 3) The gear (4 pcs) is fixed in main chassis (1). 4) The lock arm (25 and 26) and the rear lock arm (24) are fixed. 5) The spring (65) is covered over the lock slider (23). The spring (65) is assembled with through for a main chassis (1) hole. It takes care that the spring (65) does not run aground to the lock slider (23). 6) The loading slider (16) is moved back to the rear side. The lock arm (25 and 26) moving to OPEN position, and the drive arm (19) is fixed (Put in seven places boss).
23 16 65
7) The loading slider (16) is fixed on the washer (K) and the screw (B). (Torque 3±10% kgf.cm) 8) The lock arm (25 and 26) is closed by hand and the lock slider (23) is moved for close position, and the stopper (49) is fixed on the screw (B). (Torque 3±10% kgf.cm) 9) The loading cam (30) is fixed on the screw (D). (Torque 1.5±10% kgf.cm) 10) The spring (58) is fixed to the trigger slider (15) and the loading slider (16). 11) The spring (64) is fixed to the rear lock arm (24).
64
B K 19
24
15 58 1 D
30
17
|
|
|
> |
|
